MUTOOLS

mutools · Post by **mutools** » Sun Oct 08, 2017 11:40 am

https://www.mutools.com/info/docs/mulab/transport.html

mutools · Post by **mutools** » Sun Oct 08, 2017 1:33 pm

To elaborate a bit more on that info: As mentioned on that doc page, the first metronome beat (= on bar) is played at velocity 127, the next beats each at decaying velocity 100, 95,90,...
You can use that to make a metronome that plays a different sample for each beat.
See attached project, it uses samples "One", "Two", "Three" and "Four" to indicate the beats in a standard 4-beat bar

This metronome is also available as a MUX preset in MuLib:
https://drive.google.com/open?id=0B7elz ... 2N4MFk3bms

Suono & Computer · Post by **Suono & Computer** » Sun Oct 08, 2017 2:38 pm

Thank, now I try...

Suono & Computer · Post by **Suono & Computer** » Sun Oct 08, 2017 4:28 pm

Little progress... I noticed that the "create new samples from selection" function is inhibited and I can not create another sample. Does it matter that I'm using the demo version?
https://www.youtube.com/watch?v=nP0rb2a ... e=youtu.be

mutools · Post by **mutools** » Sun Oct 08, 2017 5:07 pm

Suono & Computer wrote:Little progress... I noticed that the "create new samples from selection" function is inhibited and I can not create another sample.

You need to select some audio in the sample.

Does it matter that I'm using the demo version?

No, cfr http://mutools.com/info/docs/mulab/mulab-versions.html

pljones · Post by **pljones** » Sun Oct 08, 2017 5:41 pm

-delete-
(went over the page without me noticing...)

Suono & Computer · Post by **Suono & Computer** » Tue Oct 10, 2017 7:52 am

Up to 4/4 all fine. When I try to insert a 5/4 the metronome jump a beat. So, for the 6/4 and rising. Why? Where i wrong?

https://www.youtube.com/watch?v=6h1JSKo ... e=youtu.be

Suono & Computer · Post by **Suono & Computer** » Tue Oct 10, 2017 9:06 am

An idea for a advanced metronome https://photos.google.com/share/AF1QipO ... 9kc05fQzRn

Suono & Computer · Post by **Suono & Computer** » Thu Oct 12, 2017 5:28 pm

Excuse me, did someone else check the issue shown in the video? Thank you.

mutools · Post by **mutools** » Thu Oct 12, 2017 7:37 pm

Are you sure the velocity zones are setup right? (127, 100, 95, 90, 85, ...)
If yes and you cant find the reason, pls attach the project. (zipped)

Suono & Computer · Post by **Suono & Computer** » Thu Oct 12, 2017 8:21 pm

Thanks, now it works, lowering the velocity I feel the click.

Suono & Computer · Post by **Suono & Computer** » Mon Oct 16, 2017 11:54 am

I wonder why with MuLab the time is too long to program a metronome ... If I should look at this from a commercial point of view, I would say that any musician needs certain features to be ready for use ...

Suono & Computer · Post by **Suono & Computer** » Mon Feb 25, 2019 2:39 pm

I noticed "a strange fact" in M.B. 7.7.4 - If I delete a rack, the track in the compose section does not cancel, while if I delete the track in the compose, it also erases the rack ... Is this correct? Thank you.

https://www.youtube.com/watch?v=QoHdZDx ... e=youtu.be

pljones · Post by **pljones** » Mon Feb 25, 2019 6:46 pm

The delete behaviour is intended. Note that deleting a track will not delete the targeted rack if it is targeted by other tracks or sends. (However, the rack gets deleted if it's "only" other session modular area modules that target it. I'm not so sure this is intended.)

tommyzai · Post by **tommyzai** » Mon Feb 25, 2019 8:04 pm

For me, I think some of my concerns could be addressed by creating a project template . . . maybe eight tracks or so that are ready to go based on my most common recording needs. Does what I'm saying make sense? Anyone else work from a custom project/song template? If so, any advice?

MUTOOLS

KVR Audio

Questions and Considerations on MuLab