Airwindows Single Ended Triode: Mac/Windows/Linux AU/VST

VST, AU, etc. plug-in Virtual Effects discussion
jinxtigr
KVRian
799 posts since 7 Apr, 2007 from Bellows Falls, VT

Post Sun Jun 24, 2018 5:25 pm

https://www.youtube.com/watch?v=EjF2W_okGdY

TL;DW: Unusual analog modeling effects.

SingleEndedTriode

Everybody knows that analog modeling means distortion. (well… noise and distortion. And EQ, and overprocessing… but mostly distortion.)

However, it's always the same sorts of distortion: soft or hard clipping generating harmonics. Here, have three totally different kinds!

Single Ended Triode does three things, and you don't have to do them all at once (in fact you probably don't want to).

The actual Single Ended Triode control is a special gain-staged saturation that's asymmetrical. It's a little like PurestWarm, only not, because rather than put a soft saturation on one-half of the waveform, it offsets everything and goes into the saturation with a bias voltage. Then it subtracts a related voltage, and scales the whole thing up or down based on how much distortion you're looking to get. (shown in the source code, of course)

That means you have a 'second harmonic generating' asymmetrical distortion, but with NO crossover point. Unlike PurestWarm, SET is a continuous waveshaper just like using a real triode tube single-ended, and while you can crank it up to get obvious effects, its real magic is in using just a tiny amount to warm and sweeten things. It's perhaps not ideal for the 2-buss because you'd simply be removing some of your mix energy on one half of the wave, but if the sweetening is what you need it might be worth it, because it's a super clean way to do that. It's only the asymmetrical distortion, and the interesting thing about that is: know how Spiral smooths the transition between sides of the sin() waveshaping, and that made it sound better? With Single Ended Triode, it's capable of doing that transition when cranked way up… but used subtly, the entire audio output sits within one sin() calculation, and you don't see a transition in the first place. This is literally why high end SET stereo rigs perform well for musicality and fluidness of sound: they have obvious faults but they're great at avoiding crossover issues between push/pull sides of the circuit because they don't have two sides to the circuit. It's single-ended, and so is this algorithm unless you're wildly distorting the heck out of it.

Crossover issues, you say?

Why yes. Meet Class AB (and Class B) Distortion.

This is the opposite. It adds nonlinearities as the signal passes through zero. It's a STRONG tone coloring and certainly not for the 2-buss or nice mellow music: the Class B is downright nasty and you should be careful about using it if you have delicate tweeters, as it'll create extremely harsh treble grit (though, interestingly, without Gibb effect converter clipping: that is when reconstruction of the wave makes treble go past what bass can do, when it clips the converter on highs. This is a kind that could blow your tweeters at super high volumes but does not clip the converter doing it)

The Class AB transitions through the middle of the wave in a more curvy way, causing the effect to lean towards the gritty upper-mids. Where might you find this kind of noise? Certainly not in any acoustic instrument. But… listen to certain old nasty tube Hammond organ sounds. Certain big guitar amps. Past a certain wattage, nearly every old tube amp is run push-pull (same with many transistor amps). They run hot, their calibrations drift… and one of the things that can happen to an amp is problems with that transition zone. Use Class B distortion and you'll get very much the sound of purely transistor amps breaking down and going cold and gritty. Use Class AB (because with tubes, you're probably going through output transformers and speakers that don't have hi-fi tweeters) and you'll get a bit of that gnarly rock-and-roll grit. There are expensive boutique stompboxes that can do this. Now you have it in a free, open-source plugin: open source devs, take note, because this one's not often talked about or modeled. Most attention to amplifier crossover distortion has come from High End audiophile circles, and those guys have been getting mocked for decades. This stuff will not affect a frequency response plot. In certain systems of measurement you won't even see it at all, and for years people have done naive measurement and claimed 'it's perfect, no further work needed!' and the audiophiles were tearing their hair out, swearing that certain amps sounded like butt even if they measured 'perfect'.

Little did they know that in 2018, musicians would be turning to those same horrible distortions for creative purposes, sweetening with Single Ended Triode, adding grit and attitude with Class AB distortion, and being able to put a layer of really brittle edgy brightness onto the occasional sound with Class B.

PS: some of you are having a lot of fun modeling existing hardware using elaborate combinations of Airwindows plugins. Just saying, these three sources of really specific coloration are exactly what you need to do that. Be careful of Class B as a little goes a long way (in fact, I would pick either Class AB or Class B but not both: study the circuit topology and only use AB and B where push/pull circuits actually exist, and remember they're designed not to cause this kind of problem. AB contains overlap that stops the transition point from being exactly in the middle. Apply wisely.)

This work is supported by Patreon. The more of that there is, the larger projects I can do: for instance, I can't make hardware on this budget. That could change if I keep doing better and better: I like trying to do bigger projects. For instance, it's too late tonight to stream but I've been livestreaming some modular synthesizer jams on my Youtube (and Twitch) channels, and I've got a neat new trick for next time. I've been researching a cyborg-music thing where a tiny computer (an Axoloti experimenter board) comes up with generated chord sequences that I play along to. When it goes well, it's a strange exploration into unforeseen harmonic realms. When it doesn't, I just get lost :) but I've got a new trick: retune the soloing synth to the new chords on the fly. But not over 12 notes, just 5, then it wraps! That means chord switches aren't as jarring, and a small amount of adapting to the key switch is needed, but not as much as manually/humanly adapting to an ever-changing harmonic structure. It's like it can follow melodic ideas but then throw in half-step or whole-step corrections on top of what the human's playing. You'll see (or hear). I've been saving all the Axoloti patches for all these synth jams and look forward to sharing 'em when things get good enough: at this level it's very much programming.

One final note: I need to do some rescheduling of upcoming plugins to get myself time to work on the backlog now that I'm going double speed. Things will still come out at the same pace, but I'm going to ask you this: VariMu isn't ready for next week, and I have some plugins that are. Which would you like to see, and in what order: DeRez, DrumSlam, StereoFX? DeRez is the samplerate/bitcrusher (analog style: they are continuous controls, not stepped). DrumSlam is from when I tried to do Massey TapeHead as an AU, and it didn't turn out that much like TapeHead but it did come out pretty cool. And StereoFX is a far more aggressive stereo-widener, more suited to tracks than the 2-buss.

Which would you like next week, and the week after? I'll give you them in that order. By then, I'll have other stuff in the pipeline, and I'll have the list on Patreon updated with accurate release dates. Hopefully getting DeRez and DrumSlam and StereoFX will tide you over until then :D

Halonmusic
KVRAF
1738 posts since 13 Nov, 2015 from Norway

Re: Airwindows Single Ended Triode: Mac/Windows/Linux AU/VST

Post Sun Jun 24, 2018 6:13 pm

Thanks Chris

heavymetalmixer
KVRist
272 posts since 8 Jan, 2017

Re: Airwindows Single Ended Triode: Mac/Windows/Linux AU/VST

Post Mon Jun 25, 2018 4:54 am

Wow, three saturation plugins in one, this is glorious!

User avatar
Russell Grand
KVRAF
1537 posts since 22 May, 2017

Re: Airwindows Single Ended Triode: Mac/Windows/Linux AU/VST

Post Mon Jun 25, 2018 5:27 am

:hyper:

jinxtigr
KVRian
799 posts since 7 Apr, 2007 from Bellows Falls, VT

Re: Airwindows Single Ended Triode: Mac/Windows/Linux AU/VST

Post Tue Jun 26, 2018 8:55 am

heavymetalmixer wrote:Wow, three saturation plugins in one, this is glorious!
I would have thought NONE of them were saturation plugins :D

Well, SET slider is halfway a saturation plugin…

Return to “Effects”