3dB/0.5 pole filter?

CinningBao
 KVRAF
 1803 posts since 15 Apr, 2004 from Capital City, UK
3dB/0.5 pole filter?
I'm not a coder, as such, so in my ignorance I wonder if it is at all possible to design filter circuits with slopes smaller than 6dB? or 8.3, for example..
thanks
thanks

matt42
 KVRian
 1074 posts since 9 Jan, 2006
Re: 3dB/0.5 pole filter?
Poles are just input values (in the case of a filter transfer function a complex number) that cause an equation to output infinity. So talking about 0.5 poles doesn't really make sense.
On the other hand if you can imagine a 3db low pass filter response, or 8.3, or whatever, then you can model that. Perhaps using curve fitting techniques, or some other method.
On the other hand if you can imagine a 3db low pass filter response, or 8.3, or whatever, then you can model that. Perhaps using curve fitting techniques, or some other method.

mystran
 KVRAF
 5108 posts since 12 Feb, 2006 from Helsinki, Finland
Re: 3dB/0.5 pole filter?
Single pole will give you 6dB/octave, so that's your basic building block, you can't really split it.
What you can do is use multiple 6dB/octave shelving filters placed at fixed distance from each other on the logfreq grid (eg. something like 2 such onepole shelves per octave will do the trick quite "perfectly" although you can improve the quality further by using more) and then you can control the slope freely (up to 6dB/octave) by adjusting the gain of the shelves.
Given that you need something like 1520 onepoles (per channel) to do this over the 2020kHz audible range (about 10 octaves) with more or less "transparent" results, I'd really suggest doing this with DSP rather than building a circuit.. but like... it works. If you don't mind some ripple, then using less stages is also possible. It's also worth noting that it turns out that the 3dB/octave happens to be the worstcase in terms of error, which means whatever setup can give you acceptable results for 3dB/octave will also handle anything else at least as well.
What you can do is use multiple 6dB/octave shelving filters placed at fixed distance from each other on the logfreq grid (eg. something like 2 such onepole shelves per octave will do the trick quite "perfectly" although you can improve the quality further by using more) and then you can control the slope freely (up to 6dB/octave) by adjusting the gain of the shelves.
Given that you need something like 1520 onepoles (per channel) to do this over the 2020kHz audible range (about 10 octaves) with more or less "transparent" results, I'd really suggest doing this with DSP rather than building a circuit.. but like... it works. If you don't mind some ripple, then using less stages is also possible. It's also worth noting that it turns out that the 3dB/octave happens to be the worstcase in terms of error, which means whatever setup can give you acceptable results for 3dB/octave will also handle anything else at least as well.
If you'd like Signaldust to return, please ask Katinka Tuisku to resign.

vortico
 KVRist
 219 posts since 19 Jul, 2008
Re: 3dB/0.5 pole filter?
There are a few methods for obtaining arbitraryslope digital filters.
 Construct your desired frequency response and compute the IFT to get its (infinite/noncausal) impulse response. Window it and optionally compute its minimum phase form to sacrifice phase correctness for time delay. This will have zero poles. A disadvantage is that IRs are usually only helpful if your cutoff and slope are fixed.
 Construct a frequency response and approximate it using curve fitting through composition of simpler filters (mystran's suggestion above). Biquad filters are sufficient and fast. This method doesn't preserve phase at all, if you're concerned about that.
 Realize that a 6.02dB/oct filter is just a derivative (resp. 6.02dB/oct is integration). Use a method of discrete fractional calculus to compute the 0.5th derivative, and you have a 3dB/oct filter. To get a cutoff frequency and knee instead of just a straight line in your Bode plot, split the input signal into two bands (with a HP and LP filter), pass one through the fractional filter, and mix the result.
 I haven't thought this one through, but you could construct an allpass filter that transitions from arg=0 to arg=pi at your given slope somehow and add it to the original signal to cancel high frequencies. I think this method is essentially the same as trying to construct any digital filter, but it's a different way of looking at it.
 There are of course many others that I haven't thought of before. Maybe someone has done it in the analog realm, and you could just model that.
VCV Rack opensource virtual modular synthesizer

EvilDragon
 KVRAF
 17343 posts since 7 Jan, 2009 from Croatia
Re: 3dB/0.5 pole filter?
I don't think I ever saw a 3 dB/oct filter in analog realm...

vortico
 KVRist
 219 posts since 19 Jul, 2008
Re: 3dB/0.5 pole filter?
Do you know what's going on with the Rossum Evolution? http://www.rossumelectro.com/products/evolution/ (I don't own it.) It can't do less than 3 poles but claims "continuous voltage control of the number of filter poles". Am I misunderstanding that "continuous" means noninteger number of poles? Is the module cheating by simply mixing the 3pole and 4pole signals if you specify 3.5 poles for example?
VCV Rack opensource virtual modular synthesizer

Ivan_C
 KVRian
 1077 posts since 11 Aug, 2004 from Breuillet, France
Re: 3dB/0.5 pole filter?
http://architexte.ircam.fr/textes/Helie14c/index.pdf
Simulation of fractionalorder lowpass filters, Thomas Hélie
In this paper, a new family of lowpass filters has been proposed. It allows the tuning of the cutoff frequency between 20 Hz and 20 kHz and that of the filter attenuation between 0 and 6 decibels per octave, separately and independently from one another. The realization of this family required to optimize finite dimensional approximations of an exact “diffusive representation” of the filters.
In practice, a simulation has been obtained using 13 onepoles filters, the poles of which exclusively depend on the desired cutoff frequency, and using a linear combination of their 13 outputs, the coefficients of which exclusively depend on the desired filter attenuation. This structure guarantees the stability even for timevarying parameters. In this case and with this choice, the simulation renders the memory effect due to the time variation of the cutoff frequency whereas, for the attenuation, it locally renders the output as if the attenuation had been the current value from the initial time. The results are accurate on the complete frequency range.

JCJR
 KVRAF
 2420 posts since 17 Apr, 2005 from S.E. TN
Re: 3dB/0.5 pole filter?
Passive analog pinking filters (nominally 3 dB per oct) typically used 3 or 4 cascaded, unbuffered firstorder, RC lowpass filters followed by an output buffer to present high impedance to the filter network and low impedance to the output jack.
Here is an example. I think a lot of old sources just copied one another, perhaps each time twiddling the slide rule for a few minutes to see if the previous plagarism could be "further improved".
https://www.electronicdesign.com/analog ... generator
From what little I understand, the reason it works with so few stages in analog is that usually "ideal" RC lowpass or highpass filters want to be driven by "as near zero ohm source impedance practical" and be buffered by "as near infinite output impedance as is practical".
As you let the source impedance get too high or let the destination impedance get too low (or both), the response deviates from ideal and becoming a worse and worse performing droopy filter.
So I think the analog pinking filter had interactive loading between the stages to degrade a 3 or 4 pole response down to a droopy 3 dB per octave.
It is easy to see this maddening "filter response considering source and dest impedance" in passive speaker crossover design where the source impedance isn't always "real close to zero" and the output impedance is in the same ballpark as the other components in the crossover network. It seems pretty easy to screw up and make funkydBperoctave passive speaker crossovers.
Maybe "nonideal" source and dest impedances could be somehow modeled in ZDF filters to degrade their performance like "bad analog circuits"? Dunno. If so, maybe only 3 or 4 ZDF onepoles could make as good approximation as the simple passive analog circuits? Dunno much about it.
I vaguely recall a longago post RBJ post on musicdsp mailing list, so far as I recall he explained about how to make "very lowQ" IIR filters for tasks like this. Too lazy to look it up. Typically a Q of 0.5 is as low as you go, but crappy circuit design can make the Q lots smaller!
Here is an example. I think a lot of old sources just copied one another, perhaps each time twiddling the slide rule for a few minutes to see if the previous plagarism could be "further improved".
https://www.electronicdesign.com/analog ... generator
From what little I understand, the reason it works with so few stages in analog is that usually "ideal" RC lowpass or highpass filters want to be driven by "as near zero ohm source impedance practical" and be buffered by "as near infinite output impedance as is practical".
As you let the source impedance get too high or let the destination impedance get too low (or both), the response deviates from ideal and becoming a worse and worse performing droopy filter.
So I think the analog pinking filter had interactive loading between the stages to degrade a 3 or 4 pole response down to a droopy 3 dB per octave.
It is easy to see this maddening "filter response considering source and dest impedance" in passive speaker crossover design where the source impedance isn't always "real close to zero" and the output impedance is in the same ballpark as the other components in the crossover network. It seems pretty easy to screw up and make funkydBperoctave passive speaker crossovers.
Maybe "nonideal" source and dest impedances could be somehow modeled in ZDF filters to degrade their performance like "bad analog circuits"? Dunno. If so, maybe only 3 or 4 ZDF onepoles could make as good approximation as the simple passive analog circuits? Dunno much about it.
I vaguely recall a longago post RBJ post on musicdsp mailing list, so far as I recall he explained about how to make "very lowQ" IIR filters for tasks like this. Too lazy to look it up. Typically a Q of 0.5 is as low as you go, but crappy circuit design can make the Q lots smaller!

CinningBao
 KVRAF
 1803 posts since 15 Apr, 2004 from Capital City, UK
Re: 3dB/0.5 pole filter?
Well this is fascinating, thank you everybody.
@matt42  like I said, I'm not a coder and I probably don't use the right words in the right way in this respect. I can imagine these things, but I do not have enough of a grasp on the relevant maths to build, which is why I opened the conversation here so I could hear other people talking about it in the correct way using the correct words.
@mystran  this is very interesting, yes, I could probably build something like this. I think I would probably use some technique to collapse/expand the filter frequency range as well as the gain, for sonic flexibility.
@EvilDragon  thanks have you not played with the Evolution product portico posted? "A Genus control that allows continuous voltage control of the number of filter poles (from 3 to 6 poles), essentially allowing realtime variation of Evolution’s effective cutoff slope from 18dB/oct to 36dB/oct." Sounds interesting  I wonder why they couldn't offer down to 12dB/oct
@vortico  man, I know _some_ of those words! But yes, IR's wouldn't really work in my case, and wouldn't flexible enough.. (unless they are dynamically generated, and that's a touch beyond my abilities), discrete fractional calculus (I'm going to have to look that up), I think I see what you mean about the modified allpass filter.. (going to have to read up on that as well)
@Ivan_C  fascinating stuff  so some superclever dude at IRCAM thought of this 8 years ago, did all the maths and none of it has been realised in the 'real' world? From what I can make of the paper, it does look like he's using the cascade of filters to create the fractionalorder filter, so maybe that is the only way. I wonder if he ever got round to looking at resonant fractionalorder filter..
@matt42  like I said, I'm not a coder and I probably don't use the right words in the right way in this respect. I can imagine these things, but I do not have enough of a grasp on the relevant maths to build, which is why I opened the conversation here so I could hear other people talking about it in the correct way using the correct words.
@mystran  this is very interesting, yes, I could probably build something like this. I think I would probably use some technique to collapse/expand the filter frequency range as well as the gain, for sonic flexibility.
@EvilDragon  thanks have you not played with the Evolution product portico posted? "A Genus control that allows continuous voltage control of the number of filter poles (from 3 to 6 poles), essentially allowing realtime variation of Evolution’s effective cutoff slope from 18dB/oct to 36dB/oct." Sounds interesting  I wonder why they couldn't offer down to 12dB/oct
@vortico  man, I know _some_ of those words! But yes, IR's wouldn't really work in my case, and wouldn't flexible enough.. (unless they are dynamically generated, and that's a touch beyond my abilities), discrete fractional calculus (I'm going to have to look that up), I think I see what you mean about the modified allpass filter.. (going to have to read up on that as well)
@Ivan_C  fascinating stuff  so some superclever dude at IRCAM thought of this 8 years ago, did all the maths and none of it has been realised in the 'real' world? From what I can make of the paper, it does look like he's using the cascade of filters to create the fractionalorder filter, so maybe that is the only way. I wonder if he ever got round to looking at resonant fractionalorder filter..

matt42
 KVRian
 1074 posts since 9 Jan, 2006
Re: 3dB/0.5 pole filter?
I'm kind of surprised (surprised in the sense that I've never tried to build such a filter myself and it seems to go against my intuition) that a chain of first order filters is seemingly the preferred solution.
If I get the chance I'll see how close I can get with a biquad/biquads
If I get the chance I'll see how close I can get with a biquad/biquads

CinningBao
 KVRAF
 1803 posts since 15 Apr, 2004 from Capital City, UK
Re: 3dB/0.5 pole filter?
Absolutely fascinating stuff JCJR, many thanks  I can conceptually see how misfeeding electrical circuits expecting a certain 'pressure' of signal could result in flabbyly responding components; if I had the equipment and environment to build and test this stuff, I surely would.JCJR wrote:Passive analog pinking filters (nominally 3 dB per oct) typically used 3 or 4 cascaded, unbuffered firstorder, RC lowpass filters followed by an output buffer to present high impedance to the filter network and low impedance to the output jack.
Here is an example. I think a lot of old sources just copied one another, perhaps each time twiddling the slide rule for a few minutes to see if the previous plagarism could be "further improved".
https://www.electronicdesign.com/analog ... generator
From what little I understand, the reason it works with so few stages in analog is that usually "ideal" RC lowpass or highpass filters want to be driven by "as near zero ohm source impedance practical" and be buffered by "as near infinite output impedance as is practical".
As you let the source impedance get too high or let the destination impedance get too low (or both), the response deviates from ideal and becoming a worse and worse performing droopy filter.
So I think the analog pinking filter had interactive loading between the stages to degrade a 3 or 4 pole response down to a droopy 3 dB per octave.
It is easy to see this maddening "filter response considering source and dest impedance" in passive speaker crossover design where the source impedance isn't always "real close to zero" and the output impedance is in the same ballpark as the other components in the crossover network. It seems pretty easy to screw up and make funkydBperoctave passive speaker crossovers.
Maybe "nonideal" source and dest impedances could be somehow modeled in ZDF filters to degrade their performance like "bad analog circuits"? Dunno. If so, maybe only 3 or 4 ZDF onepoles could make as good approximation as the simple passive analog circuits? Dunno much about it.
I vaguely recall a longago post RBJ post on musicdsp mailing list, so far as I recall he explained about how to make "very lowQ" IIR filters for tasks like this. Too lazy to look it up. Typically a Q of 0.5 is as low as you go, but crappy circuit design can make the Q lots smaller!
I'm not sure any of the standard modular DSP environments emulate electronics well enough (except possibly Spice? or Reaktor core..) to just build an unstable circuit..
You have given me a lot of food for thought, and a lot of things to read up.. I wonder if any developers will choose to explore these unstable filter designs in commercial synths/effects. I notice Cytomic's Scream internal diodes and other components can be altered with the use of external files, but since I don't have it, I can't experiment.

JCJR
 KVRAF
 2420 posts since 17 Apr, 2005 from S.E. TN
Re: 3dB/0.5 pole filter?
Hi CinningBao. Please take my comments skeptically as I'm not an authority.CinningBao wrote:You have given me a lot of food for thought, and a lot of things to read up.. I wonder if any developers will choose to explore these unstable filter designs in commercial synths/effects. I notice Cytomic's Scream internal diodes and other components can be altered with the use of external files, but since I don't have it, I can't experiment.
I don't think you would call "suboptimal analog passive filter networks" unstable. Especially if such networks do not contain inductors or "artificial inductors" they are stable as a brick They just have limp response curves.
But sometimes a limp response curve is what an engineer would want, such as a pinking filter to turn white noise into pink noise, 3 dB per octave. So I think the low parts count versions of such are smart old analog engineers cunningly intentionally designing limp circuits which just happen to be 3 dB per octave limp over the audio band.
I don't know if anyone ever made a tunable pinking filter, but one could copy one of the old example circuits and put "voltage controlled resistor" elements of one or the other kind to replace the resistors then it could be swept. But because the typical pinking filters were intended to filter the entire audio band at that slope, sweeping that exact circuit might not have strong audible effect.
In other words the three or four pole passive analog pinking filter was designed to be "fairly pink" from maybe 20 to 20 kHz (or a narrower band) and would probably need more parts to continue the 3 dB slope beyond that range. So sweeping that exact filter would be somewhat audible because swept higher, it would stop being 3 dB / oct in low freqs (perhaps a flatter bass response). Swept lower, it would stop being 3 dB / oct in high freqs (perhaps a gradually higherslope HF response above some breakpoint). But over several octaves of sweep the mids ought to sound about the same, offering only subtle tonal variation to the ear, though the overall output amplitude would rise if you sweep the filter higher and the overall output amplitude would fall if you sweep it lower..
A swept pinking filter would maybe need modifying so it is fairly flatresponse below a corner frequency and then pink above the corner frequency, so you could sweep the corner up and down similar to steeper swept lowpass filters. Even then possibly a "fairly subtle" audible effect.
I never mastered the math well enough to remember it well, but analog passive filter networks made of resistors, capacitors and inductors are analyzed by EEs with sdomain transfer function equations. You can google it and find lots of explanations, plus there are many textbooks about this. Some people take to the math better than others. The "s" is a complex variable with real and imaginary parts, so when it comes to doing algebra with the equations, it follows somewhat fancier rules than simple real algebra. A lot of references assume that the reader ALREADY KNOWS that s is a complex variable. So if the reader DOES NOT KNOW about that then he can get easily confused trying to follow the math.
Those s domain transfer function equations encapsulate the phase and amplitude response for all frequencies in one handy little (mindnumbing) equation.
So a practitioner could take that simple fourcapacitor pinking filter in the article I linked and construct an sdomain transfer function equation describing it. Furthermore, the sdomain equation could be converted into a zdomain (digital "discrete" audio) equivalent, for instance using bilinear transform. Then the coefficients from the zdomain equation would in theory (and probably in practice) be able to be placed into simple IIR computer filter code and get about the same limp response. It is "most similar" for audio bandwidth at higher sample rates. At 44.1 k or 48 k samplerate there are analogvsdigital differences that get noticeable in the higher frequencies, blamed on the bilinear transform "frequency warping".
Mystran mentioned cascades of shelving filters. A shelving lowpass filter mixes part of the input audio along with part of the filter output to give an "adjustably limp" response.
Maybe mixing thataway for a shelf gives exactly the same result as "loading down" the output of a passive analog filter network? Or maybe they both give limp responses, but the nature of the limp responses are completely different? Dunno.

aciddose
 KVRAF
 12117 posts since 7 Dec, 2004
Re: 3dB/0.5 pole filter?
Most analog "pinking" filters are actually red (6 dB) filters but rarely two shelving filters have been used to produce "approximately reddishpink".EvilDragon wrote:I don't think I ever saw a 3 dB/oct filter in analog realm...
Free plugins for Windows, MacOS and Linux. Xhip Synthesizer v8.0 and Xhip Effects Bundle v6.7.

aciddose
 KVRAF
 12117 posts since 7 Dec, 2004
Re: 3dB/0.5 pole filter?
Unfortunately you're talking about pure fantasy here. You get 20 dB per decade or nothing. There is no "half way filter" regardless of impedance or so on. It's simply impossible.JCJR wrote:Maybe mixing thataway for a shelf gives exactly the same result as "loading down" the output of a passive analog filter network? Or maybe they both give limp responses, but the nature of the limp responses are completely different? Dunno.
The way the filters work is nothing like what you imagine: it's rather a simple matter of amplitudes. You're just mixing multiple 6dB (or multiples of) slopes and the resulting slope is that combination of "steps".
For example let's imagine we're working with ideal 6 dB slopes (trapezoidal edges). So we have our first stage set at 100 Hz. At 200 Hz the amplitude is now  6dB.
It would be nice if I could quickly plot the graphs of this stuff but maybe later...
So we set up another stage at 200 Hz this time and mix it at 3 dB amplitude with the first stage. We'll now have a "wobble" with a step that flattens to 3 dB at 200 Hz then continues at 6 dB beyond that point. If we want to improve the slope we can add more filters.
The ideal result is one filter per octave but that isn't needed usually since our ears are barely sensitive enough to detect differences in a 6 dB slope to begin with. So alternatively we can allow for more "wobble" in the slope and space our filters out like 100 Hz, 1000 Hz, 10000 Hz at the correct amplitudes of 10, 20, 30 dB instead.
Free plugins for Windows, MacOS and Linux. Xhip Synthesizer v8.0 and Xhip Effects Bundle v6.7.

JCJR
 KVRAF
 2420 posts since 17 Apr, 2005 from S.E. TN
Re: 3dB/0.5 pole filter?
Thanks Aciddose. A "properly output buffered" RC lowpass, so far as I know, will be 3 dB at Fc (the freq where the impedance of the resistor and capacitor are equal), and about 6 dB one octave higher. And then it will settle down to about 6 dB per octave above [Fc + 1 octave]. So the properly buffered firstorder filter is "in the rough ballpark of 3 dB per octave" for 1 or 2 octaves, depending on how picky you are about expectations. Loosely speaking it is "about 3 dB per octave" from about [Fc  1 octave] up to [Fc + 1 octave]. It "makes sense" in analog where folks often use 5+ percent tolerance components and only have a few dozen standard choices of component values.aciddose wrote:Unfortunately you're talking about pure fantasy here. You get 20 dB per decade or nothing. There is no "half way filter" regardless of impedance or so on. It's simply impossible.JCJR wrote:Maybe mixing thataway for a shelf gives exactly the same result as "loading down" the output of a passive analog filter network? Or maybe they both give limp responses, but the nature of the limp responses are completely different? Dunno.
The way the filters work is nothing like what you imagine: it's rather a simple matter of amplitudes. You're just mixing multiple 6dB (or multiples of) slopes and the resulting slope is that combination of "steps".
For example let's imagine we're working with ideal 6 dB slopes (trapezoidal edges). So we have our first stage set at 100 Hz. At 200 Hz the amplitude is now  6dB.
It would be nice if I could quickly plot the graphs of this stuff but maybe later...
So we set up another stage at 200 Hz this time and mix it at 3 dB amplitude with the first stage. We'll now have a "wobble" with a step that flattens to 3 dB at 200 Hz then continues at 6 dB beyond that point. If we want to improve the slope we can add more filters.
The ideal result is one filter per octave but that isn't needed usually since our ears are barely sensitive enough to detect differences in a 6 dB slope to begin with. So alternatively we can allow for more "wobble" in the slope and space our filters out like 100 Hz, 1000 Hz, 10000 Hz at the correct amplitudes of 10, 20, 30 dB instead.
Even if the ultimate 20 dB per decade might still hold in a "loaded down" RC circuit, the transition shape between "flat" and "6 dB/oct" gets wider and sloppier the more you load it down. Along with more insertion loss and such.
Breadboard a cascade of 2 or 4 simple RC lowpass, each stage 10 kohm resistors, 0.016 uF caps.
_A_ Drive the cascade completely unbuffered from a 10 kohm source into a 10 kohm destination and plot the curve.
_B_ Now put fet opamp voltage follower buffers on the input and output and inbetween each RC stage and plot the response.
The fullybuffered version will be a lessdroopy better response over several octaves in the middle around Fc. The unbuffered version will make you want to cry.