Tritik releases KrushPro (v1.1.0)

[Shalotta]

Is copy & paste of modulation settings possible?
Let`s say seq 1 -> seq 2.

[jbraner]

Thank you all for your feedback!

Hello, why is there some latency in Wavecrush? (Just asking.) Like this plugin a lot.

I'm not sure what "sync" and "morph" actually do - in the wavecrusher module.

The Wavecrush module is built around an original distortion algorithm, based on the transformation of wavesets. Wavesets (as defined by Trevor Wishart) are short segments of the sound signal defined between pairs of zero-crossings. This is the extraction of those audio segments that implies some latency.

The extracted wavesets are then transformed (note that there is a small waveform next to the 'Wavecrush' which helps visualising that) :



morph allows you to gradually transform each waveset to the waveform that is selected in the menu below the knob.
- if 'morph' is at 0 then the wavesets are left untouched.
- if 'morph' is at 1 then the wavesets are fully replaced by the selected waveform

width progressively 'squeezes' the wavesets. Note that the control is reversed :
- when the width is at 0% the wavesets are left untouched.
- when the width is at 100% the wavesets are fully zeroed.

sync : each waveset is repeated faster than normal speed during the original waveset duration.
- at 0%, each waveset is played normally.
- at 100%, each waveset is repeated 16 times at a 16x speed.

In the case of basic sounds (sine, square, saw,..) it's interesting to note that a waveset corresponds to a period of the signal, and the timbre modification can be warm and gentle (try it on simple synthesizers oscillators).
But for the more common case of complex or non periodic signals those wavesets do not correspond to any kind of 'period', and that leads to much more complex/drastic/deliciously dirty distortions effects!

Hi Tritik,
Thank you! That's exactly what I was looking for
You really should have a short "manual" with stuff like this in it

So my next question is - what is the format of the "wavetables" that this module uses? There is a user directory, and I put a few wavetables in it - but they weren't recognised. My wavetables seem a lot bigger than these ones.

[Tritik]

what is the format of the "wavetables" that this module uses?

wav or aiff audio files, 2048 samples long.

Is copy & paste of modulation settings possible?
Let`s say seq 1 -> seq 2.

yes! you can do that with Alt+drag
cf the tip at the bottom left of this page : https://www.tritik.com/products/krushpro/#tips

[Shalotta]

yes! you can do that with Alt+drag
cf the tip at the bottom left of this page : https://www.tritik.com/products/krushpro/#tips

Cool, thanks.

In a way this is a different beast than the free version, still lightweight.
Thoughtful and tidy layout, intuitive.

Worth to try on live drums: adjusting Bitchrush drive plus Wavecrush sync ... c'est magnifique.

[Vortifex]

..

[jbraner]

jbraner wrote: ↑
Sat Jun 15, 2019 9:44 pm
what is the format of the "wavetables" that this module uses?

wav or aiff audio files, 2048 samples long.

So they're not really wavetables - more like single cycles? (I have loads of these too)

[Tritik]

So they're not really wavetables - more like single cycles?

Well, they are single-cycle wavetables!
But support for multiple wavetables and morphing between them would be really interesting, I'll think about adding that in a future version, thanks!

Just bought it. Already had the free one but this is really nice.

Thanks!

[jbraner]

So they're not really wavetables - more like single cycles?

Well, they are single-cycle wavetables!
But support for multiple wavetables and morphing between them would be really interesting, I'll think about adding that in a future version, thanks!

That's OK, I was just checking the terminology. I have loads of wavetables and single cycle files - I'll try copying a few single cycles over - and see if they work

[Tritik]

No important issues have been reported until now. This beta version seems quite stable!
Please drop a message via the contact page if you bump into anything that needs to be fixed.
v1 should be released next week!

[scott_free]

Does Krush Pro have internal oversampling?

Edit: Thanks for the response below.

[Jonathan Shepherd]

All is kosher here in Podium and Reaper 64. Ace job sir! Great sound and I quite like the modulation setup. Good day-

[Tritik]

Does Krush Pro have internal oversampling?

not at the moment but I plan to add an oversampling option in a future update.

All is kosher here in Podium and Reaper 64. Ace job sir! Great sound and I quite like the modulation setup. Good day-

Thanks!

[Tritik]

Just a heads-up that KrushPro v1 will released soon (June 25th), so there's only a couple of days left for 50% discount pre-order.

[s28]

The stereo modulation in this plugin is amazing. So much movement.

[Tritik]

The stereo modulation in this plugin is amazing. So much movement.

Thanks!
As far as I know KrushPro is the first plugin with full stereo modulations capabilities (with every modulation signal and all the LFOs, step sequencers, etc. being stereo)