XT Software

DarkStar · Post by **DarkStar** » Tue Aug 17, 2004 11:02 am

Btw, can you explain me the following:
In the audio editor, when I select the audio clip there's another wave form poping up at the bottom of the window. I found out that I can resize the audio clip by draging the two little squares left and right. But there seems not to be an option to make those squares snap to the grid. If that's true it's entirely luck whether the clip is still in sync after editing - especially since you cannot zoom in vertically.

Pädy,
That waveform at the bottom is the one you are currently working on (I call it the Clip Editor) You can have several clips on an audio channel in the Audio Part and several channels. And you are right, the squares do not snap.

This might do what you want:
- set Snap to the desired value,
- zoom in at your desired start point for the clip, using Ctrl+mousewheel over the position, in the upper waveform
- position the start of the clip as desired
- then, in the clip editing panel (the lower waveform), drag the left hand square to the right
- you should see the waveform content of the upper clip move to the left.

- when it is Ok, use Edit/Copy and Edit/Paste to place the clips where you want them

HTH

DarkStar · Post by **DarkStar** » Tue Aug 17, 2004 11:07 am

jens wrote:
Pädy wrote: And please, can we resize the beginning of a part too. That's normally where I have to adjust the part.

Cheers, Pädy
Yes, I second this

I've been longing for this for a long time - why I never brought it up is beyond me

Jens,
Perhaps you were a bit distracted playing with your metronome and count-in

And I would like to see
both Snap to the Snap grid,
and Snap by the Snap interval (as it is now)

jens · Post by **jens** » Tue Aug 17, 2004 11:20 am

Simon I wrote:
jens wrote:
Pädy wrote: And please, can we resize the beginning of a part too. That's normally where I have to adjust the part.

Cheers, Pädy
Yes, I second this

I've been longing for this for a long time - why I never brought it up is beyond me
Jens,
Perhaps you were a bit distracted playing with your metronome and count-in

And I would like to see
both Snap to the Snap grid,
and Snap by the Snap interval (as it is now)

agreed

Pädy · Post by **Pädy** » Tue Aug 17, 2004 6:01 pm

Thanks Simone I for your explanation.

Any official word on the subjects and FR? Just curious.

DarkStar · Post by **DarkStar** » Tue Aug 17, 2004 8:12 pm

No problem.

The only official word I can offer is eXTraordinarily good.

I am aiming to publish an updated FR list tomorrow.

Pädy · Post by **Pädy** » Mon Aug 23, 2004 3:01 pm

Another update and no mention of fixing the ASIO.dll problem. I haven't tested it again though, maybe you fixed it but didn't list it on the release notes. Anyway, hopefully I'm not too impatient but I really consider this to be an important issue, so some official word when we can expect this to be fixed would be much appreciated.

Cheers, Pädy

jorgen · Post by **jorgen** » Mon Aug 23, 2004 3:41 pm

Hi, I haven't found the problem yet. Working on it. Next beta is out few days after 7th september. Hope to have fixed it then...

jorgen

asseca · Post by **asseca** » Mon Aug 23, 2004 4:06 pm

Jorgen,

At last going on a well deserved holiday

If so, have a good time

Pädy · Post by **Pädy** » Mon Aug 23, 2004 4:56 pm

Thanks jorgen for the statement.

Have a nice holiday.

Cheers, Pädy

adds2one · Post by **adds2one** » Mon Aug 23, 2004 8:58 pm

Simon I wrote:
jens wrote:
Pädy wrote: And please, can we resize the beginning of a part too. That's normally where I have to adjust the part.

Cheers, Pädy
Yes, I second this

I've been longing for this for a long time - why I never brought it up is beyond me
Jens,
Perhaps you were a bit distracted playing with your metronome and count-in

And I would like to see
both Snap to the Snap grid,
and Snap by the Snap interval (as it is now)

Here Here!! Resizing the beggining of a part would make working so much smoother.

Have a great well deserved holiday Jorgen.

Pädy · Post by **Pädy** » Sun Nov 21, 2004 1:01 am

Hi Jorgen,

Had a look at the current update and apparently the problem is still there. All output signals are roughly 6 dB below the live input signal. Any news on this?

Cheers, Pädy

jorgen · Post by **jorgen** » Mon Nov 22, 2004 1:50 pm

Pädy, I'm on it.

jorgen

Pädy · Post by **Pädy** » Wed Jun 22, 2005 5:09 pm

Sigh.

Jorgen, the current build still is 6 dB below the live input signal.
I mainly use Guitar Rig for live playing. eXT is superb for jamming along and recording live stuff in an easy fashion. But... this bug is now in there for as long as I can think with no attempt of yours to fix it. What is it? Do I have to explain the problem again? Can't you reproduce it? What do I need to do for you to fix this. I'm sure this is something trivial, maybe just a typo. Please, fix it.

jorgen · Post by **jorgen** » Wed Jun 22, 2005 5:26 pm

Hi, right-click sequencer comp and select "inputs and outputs", then unlink the first Stereo input so that you get 2 mono instead.

Then route your line in (mono isnt it?) to the first mono input of the sequecner.

You may have to do the same with Master in comp, Im not sure what input configuration your asio driver has and what intputs you have enabled in audio setup.

The trick is to make sure there is no mono to stereo convertion.

cheers
jorgen

XT Software

KVR Audio

Feedback to Beta 15 Aug 2004