KVR Audio

Goseba · Post by **Goseba** » Fri Jul 22, 2005 7:45 pm

Just dowwnloading the demo so have not tried it yet but the mp3 examples sound good.
I have seen you can load your own wavs which is good, but is there a text list of all the original words to see what is included?

sonicfire · Post by **sonicfire** » Fri Jul 22, 2005 7:49 pm

Hi goseba, i will make a list of all words included so far and will put that into the *.pdf manual!

Goseba · Post by **Goseba** » Fri Jul 22, 2005 8:30 pm

Just installed the demo and all that is picked up is the talkbox dll, it does not see the Robocoder dll, any ideas?

Goseba · Post by **Goseba** » Fri Jul 22, 2005 8:41 pm

Goseba wrote:Just installed the demo and all that is picked up is the talkbox dll, it does not see the Robocoder dll, any ideas?

Just loaded it onto my main music PC and it is ok. Is there a demo of the vsti though?

sonicfire · Post by **sonicfire** » Fri Jul 22, 2005 10:31 pm

@goseba: at the moment not, thats the default demo-limitation that it comes as VST FX only

conny_kvr · Post by **conny_kvr** » Sat Jul 23, 2005 1:06 am

Hi - Got the 1.0 and have the same problem as with the beta:
In Live, when saving a Live set with Robocoder, the preset does not produce any sound until I change it and change it back.
Some initializing problem?

Guess same is the case in Bidule.

// C

conny_kvr · Post by **conny_kvr** » Sat Jul 23, 2005 1:14 am

And because Bidule does not accept duplicate ID's, the Robocoder and Robocoder_I gets an error when MDA TALKBOX.DLL has the same ID in both installations.
No sound.

// C

Micha · Post by **Micha** » Sat Jul 23, 2005 11:56 am

No sound in FLS again:
Same problem back:
I save a project where Robocoder plays ok and reload this song, I have no sound. I have to "reload current plugin" and the right preset. Then it works again. So Robocoder seems not to be initialized in the right way! Thanks for your patience

sonicfire · Post by **sonicfire** » Sat Jul 23, 2005 12:40 pm

@conny_kvr: i will upload the plugin with two seperate ID´s today! about that initialization thing - not sure what i can do about it but i´ll take a look!

@micha: i tried it with FLS Demo. When i save and reload the project it goes fine, but i noticed it wouldn´t load correct (doesnt switch preset) when i restart FL completely. this is strange and again one of those problems where i´m not sure what i can do about

by the way: i had no sound problems!

EDIT: when i load a different project in FL first (no Robocoder used) and then a project with robocoder, it works correct! so i guess a temporary fix would be when starting FL load a different project first, then the "robocoder-using one"

Micha · Post by **Micha** » Sat Jul 23, 2005 1:13 pm

Sorry, can't confirm your EDIT.
Tryed it with FLS freshly started and load new project inside loaded FLS. Only my method works here.

conny_kvr · Post by **conny_kvr** » Sat Jul 23, 2005 2:25 pm

Another thing:
I have a sequence in Live that runs all the slots in Robocoder top to bottom.
When I switch the mode a.adv off while sequence is running, one slot light hangs and that slot will then not produce sound.

// C

conny_kvr · Post by **conny_kvr** » Sat Jul 23, 2005 2:29 pm

Anmnd quite often I can't get the x/y modulation to move automatically, although a mode is choosen, speed is set and the targets are set up and I have set it to loop.

// C

sonicfire · Post by **sonicfire** » Sat Jul 23, 2005 4:50 pm

I will see, what i can do!

odo · Post by **odo** » Sat Jul 23, 2005 4:53 pm

also a id Problem

but i like the plugin

Odo

sonicfire · Post by **sonicfire** » Sat Jul 23, 2005 6:37 pm

thanks, odo!

ok, i will update the robocoder in the next hours!

robot vocal phrase generator VSTi