The KXOMNI-600 VER 2.0 is avaliable now !![Freeware]

34 posts

RELATED
PRODUCTS

The KXOMNI-600 VER 2.0 is avaliable now !![Freeware] 2006-07-09T10:55:49+00:00 Version 2.0 of the KXOMNI-600 is available. I have worked for several months on two new modules, an oscillator and a wavform generator. Benefitting from the knowledge acquired during this development, I began at the beginning of June a new version of my KXOMN plugin. I use modules written in C++ to complete the SE modules, KXOMNI-600 uses 8 additional SEM modules. By using a gnu IDE (code:: bloks) and by optimizing my code, I have gained approximately from 10 to 20% on the total CPU use of the KXOMNI (according to the presets). Here the list of the innovations of version 2.0: >>> filter KX LPF: You finally will be able to adjust resonance as you like … It now supports the noise modulation. The adjustment of the cut-off frequency is more precise (5v=440hz, 6v=880hz). That makes it possible to play with the filter auto-oscillation. It have 4 new modes: -HQ, the filter auto-oscillation are generated without audible distortion and his level is stable ( 55hz to 14080hz). - HQS, identical mode, addition of a distortion on the auto-oscillation. - HQM, resonance are regulated around the auto-oscillation limit, that allows a finer adjustment of resonance. - HP, simple Hi Pass 4 poles without resonance. The old resonance modes, off, Lo, Hi, Hi+, SE, Lo+, are identical of the 1.30 version except the adjustment of the cutoff…. The mode "off" makes it possible to save CPU if you do not use resonance. >>> SE filter was removed and replaced by a bypass, if you do not want to use the filter that saves CPU. >>>new curves of the envelope generators of Vcf and the oscillators The curves have a mode L which is a compression of the envelope generator signal, the Eg level is reached more quickly and it is maintained longer. >>> mode L also exists for Vca ("comp" parameter). >>> the oscillator waveshapers incorporates a bypass and the Exp-Inv++ curve was optimized (CPU saving). >>>the oscillator filters have mode HQM (see above) and also a bypass (CPU saving). The oscillator "Hz" of KXMOD section modulates this filter instead of modulating Vcf. >>> the oscillator "Hz" wavform can be changed and it can directly modulate the 4 oscillators and their filters. >>>Now, you can replace the vu-meters by an oscilloscope, analyzers of frequency, Leds. >>>the fx section now has a distortion with an feedback adjustment and an ON/OFF(CPU saving). Corrective measures: >>>the Vca velocity control is regulated now gradually. >>> the Gain value is limited… from 0.4 to 1.6. /*************************/ Important notes ! The filename is V2-KXOMNI-U3.dll, I changed it to enable you to install the 2.0 version without erasing the 1.30 version file. The adjustment of the cutoff is different compared to the version 1.30, if you load your old presets, it will be necessary for you to readjust the cutoff. Of-course, I changed my SEM modules… do not hesitate to inform me if you find some bugs !!! By safety I will make a version with my modules compiled with Borland Free. THE PLUGIN KXOMNI-600 IS A FREEWARE… THE ONLY POSSIBLE THING THAT I ASK YOU IN RETURN , IF YOU LIKE THIS PLUG, IS TO MAKE SOME PUBLICITY ABOUT IT ON THE NET FORUMS. direct download : KXomni600-U3.zip kx77free.free.fr Xavier Kalenky 07/07/2006 kx77free https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=75331

Polymerick Polymerick https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=3092: KVRist
Contact Polymerick

Website; 67 posts since 19 Jun, 2002 from Bordeaux, France; Contact:
Contact Polymerick

Website

Post by Polymerick » Sat Jul 22, 2006 7:44 am

0
Quote

I love your synth (thanks to audiofanzine !), GUI is a bit complex but what a sound !

Ne tombez pas dans l'oreille d'un sourd !
Polymerick Sonic Elucubrations

Reverse Engineer Reverse Engineer https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=9129: KVRAF; 4968 posts since 23 Sep, 2003 from Glasgow

Post by Reverse Engineer » Sat Jul 22, 2006 8:29 am

0
Quote

Absolutely brilliant synth. It's very much appreciated that you're gifting this to us all.

kx77free kx77free https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=75331: KVRian
Contact kx77free

Website; Topic Starter; 725 posts since 19 Jul, 2005 from Paris; Contact:
Contact kx77free

Website

Post by kx77free » Fri Jul 28, 2006 9:20 am

0
Quote

Hi,

Here my new KXOMNI demonstrations very KX and 80's...

DEMO1 (WMA, 4.1 mo)
NFX+KXdelay2 (WMA, 3.8 mo)
DEMO3 (WMA, 7.3 mo)

http://kx77free.free.fr

GaryG GaryG https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=5399: KVRAF
Contact GaryG

Website; 8111 posts since 13 Jan, 2003 from Darkest Kent, UK; Contact:
Contact GaryG

Website

Post by GaryG » Thu Aug 17, 2006 11:53 pm

0
Quote

Just got around to trying this synth out: some truly amazing sounds in there!

I need to spend a lot of time figuring everything out but I think it's worth it.

Nice one.
.g

https://lighthugger.bandcamp.com

Post Reply

34 posts

Return to “Instruments”