KVR Audio

mx25 · Post by **mx25** » Wed Dec 24, 2014 1:16 am

Because of my mistake, I uploaded a demo asking serials, so no sound came out.

Now I have added a new demo with 1200 presets and sound output.

(new 1.99d)
Work fine and available on the synthblitz site.
http://synthblitz.altervista.org/nitroflex.html

Numanoid · Post by **Numanoid** » Fri May 22, 2015 3:58 pm

Thanks for yet another free update, got it today

mx25 · Post by **mx25** » Sat May 23, 2015 3:21 pm

unison improved with the addition of new features. Improved the reverb, and added an internal filter to further enhance the sound quality.
There's even more than this ...

mx25 · Post by **mx25** » Wed Aug 12, 2015 12:45 pm

I have released version 1.99.4 with more adjustments and a new parametric equalizer that improves the sound,also 100 new presets to replace those unnecessary or annoying,and more new.

Please, those that have not received the update can write to Synthblitz Audio or communicate the new email where I can send the update.

Many Thanks

Numanoid · Post by **Numanoid** » Thu Aug 13, 2015 8:07 pm

Thanks for the update

mx25 · Post by **mx25** » Sat Aug 15, 2015 9:39 pm

Thank you always

in addition to the parametric equalizer I added the setting "hold" on the envelope, repaired the scale of the arpeggiator that shows also the number of selected note, and raised the number of points for the waveform \ wavetable, it is now fully compatible with the 'high-quality waveforms that can be loaded from the outside, such as galbanum.
I can start to create a new block of presets that will be added to the 1200 that are loaded into the synth

Numanoid · Post by **Numanoid** » Sun Aug 16, 2015 4:18 pm

Thanks for the latest update, have been playing with it, works fine

emef · Post by **emef** » Fri Feb 16, 2018 10:31 am

i saw that Nitroflex got updated to 2.5
are you Nitroflex users still getting emails with the new versions?
the last email i got with a new version attached was 2.21

mx25 · Post by **mx25** » Fri Feb 16, 2018 12:15 pm

Hello,within a few hours the link for the update will be distributed in the registered emails

egbert101 · Post by **egbert101** » Fri Feb 16, 2018 12:57 pm

Halonmusic · Post by **Halonmusic** » Fri Feb 16, 2018 3:20 pm

Probably because its made with Flowstone. Not a problem for me as i got several synths and plugins made with FS

egbert101 · Post by **egbert101** » Fri Feb 16, 2018 3:31 pm

Halonmusic · Post by **Halonmusic** » Fri Feb 16, 2018 3:40 pm

egbert101 wrote:
Halonmusic wrote:Probably because its made with Flowstone. Not a problem for me as i got several synths and plugins made with FS
Well the noise every five seconds in the demo and the buggy delay or reverb certainly put me off it.

Its years since i tried it but I remember it being buggy.

mx25 · Post by **mx25** » Fri Feb 16, 2018 7:09 pm

emef wrote:i saw that Nitroflex got updated to 2.5
are you Nitroflex users still getting emails with the new versions?
the last email i got with a new version attached was 2.21

I hope you got the link. Many emails from 2012 to 2014 and also recent ones, come back as non-existent or user-spam blocking.
Those who have not received the update can request it by providing a valid email address.
Many thanks for the reports

Distorted Horizon · Post by **Distorted Horizon** » Fri Feb 16, 2018 7:25 pm

Halonmusic wrote:
egbert101 wrote:
Halonmusic wrote:Probably because its made with Flowstone. Not a problem for me as i got several synths and plugins made with FS
Well the noise every five seconds in the demo and the buggy delay or reverb certainly put me off it.
Its years since i tried it but I remember it being buggy.

Knobs were a bit fiddly if I remember right. But the dev was very friendly and a nice person

Nitroflex vst