KVR Audio

Download SOphist · Post by **Download SOphist** » Sat May 23, 2009 8:28 pm

this may still be a fine day after all!
thanks bootsie!

Cooker · Post by **Cooker** » Sat May 23, 2009 8:40 pm

Liked it with bass'n drums most. Not very subtle but nice for a free plug-in.

freddemillio · Post by **freddemillio** » Sat May 23, 2009 9:49 pm

Maybe a minor bug or maybe a feature or maybe ...?

When using on a mono track in Cubase SX3, the meter needles (both red and grey) will only go to -5 dB. Seems like that with one track instead of two, the meter is cut in half. Other than that it seems to be working on the audio in a normal fashion. So no big deal and does not get in the way of using it. Still, I thought I might as well report it.

michat · Post by **michat** » Sat May 23, 2009 10:17 pm

long-awaited.
Finally there.

Can't wait to try, although it seems that I can test it tomorrow soonest

kylen · Post by **kylen** » Sat May 23, 2009 10:34 pm

I'm not getting the GUI in Reaper 2.58 - maybe it's a setting on my side...

DL'd again from Booty's link and reinstalled - now GUI shows up - I think all is well, must've dropped a bit somewhere across the ether...

Thanks Bootsie!!!

jmh · Post by **jmh** » Sun May 24, 2009 1:40 am

Yet another killer from Bootsy.

One of these days I'm going to have to father a child so I can ask for an address to ship my firstborn to.

sunny_j · Post by **sunny_j** » Sun May 24, 2009 10:00 am

is this what bootsie was referring to as passband ripple caused by the oversampling feature??

kmonkey · Post by **kmonkey** » Sun May 24, 2009 10:17 am

Yes it is. But not all curve lines on that screenshot. Just top right one i think. I know this is looking weird but it is not so audible as it may appear in that graph... Like someone said it's a trade off...

IMO best oversampling implementation is done by Voxengo.

This plugin is soooooo nice!!

sunny_j · Post by **sunny_j** » Sun May 24, 2009 10:43 am

can this be avoided in any way? could butterworth filters have been used to avoid this? perhaps someone "in the know" can chime in. bootsie perhaps?

bootsie · Post by **bootsie** » Sun May 24, 2009 11:10 am

The analyzer gets somehow 'confused' if the transient circuit gets dialed in, maybe it's interpreting it as further delay/phase. It shows only correct graphs when the dial is straight to the left. And then you see a little ripple actually caused by the filter and the phase.

It's the same with my new Transient EQ modules (the XTC thing) where when dialing in EQ based on transient flow the analyzer shows completely wrong graphs.

sunny_j · Post by **sunny_j** » Sun May 24, 2009 11:19 am

hey bootsie thanx for the response.

P.S. when will tesslaSE be updated like u mentioned sometime earlier. i get good results using both these together

sunny_j · Post by **sunny_j** » Sun May 24, 2009 11:29 am

--nevermind--

K-Slash · Post by **K-Slash** » Sun May 24, 2009 11:56 am

Yeah, I'm also waiting for the TesslaSE mkII

.

I use TesslaPRO on full mixes to bring some "mojo".

And use TesslaSE on individual tracks, especially drums parts, for getting them HOT !

Like a saturator/clipper actually.

bootsie, any word

?

bootsie · Post by **bootsie** » Sun May 24, 2009 2:38 pm

K-Slash wrote:Yeah, I'm also waiting for the TesslaSE mkII .

There won't be a mkII version of it just a re-compiled and slightly optimized version. It will be sound/feature-wise 100% the same. It will probably appear in the first week of June.

KingofBeers · Post by **KingofBeers** » Sun May 24, 2009 4:44 pm

Hats off to you bootsie, this is a bloody good plugin, and for free, my god its better than many highend plugins!!!!, it really gives you that body you always wanted!!

Cheers.

TesslaPRO (update v1.0.1)