good news for fl studio owners
-
- KVRist
- 90 posts since 19 Feb, 2005 from uk
you might allready know this but have you found a way to sync your analog gear to fl 5.?????example:if i was to plug say a philip rees mds24 sync box into the midi out of fl studio,didnt matter what i tried it would never give me a clock output ,this you can tell because the mds24 box has an led light that flashes when it receives a clock pulse.i have now solved the problem and will share it with any one.:}
[k-v-r-i-s-t-h-e-b-e-s-t]
-
- KVRAF
- 3139 posts since 6 Sep, 2002 from United Kingdom & Opinions Will Travel :O)
You could use the master sync output option from the midi dialogue box from within FL?
Best regards,
Spe3d
:O)
Best regards,
Spe3d
:O)
-
- KVRist
- Topic Starter
- 90 posts since 19 Feb, 2005 from uk
ive tried that but it wont make the led flash on mds24 so i know its not working.
[k-v-r-i-s-t-h-e-b-e-s-t]
-
Programentalist Programentalist https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=8597
- KVRian
- 657 posts since 21 Aug, 2003
-
- Rad Grandad
- 38041 posts since 6 Sep, 2003 from Downeast Maine
I sync just like spe3d says...c'mon it couldn't be any more simple...it wont slave but it will master.
The highest form of knowledge is empathy, for it requires us to suspend our egos and live in another's world. It requires profound, purpose‐larger‐than‐the‐self kind of understanding.
-
- KVRist
- Topic Starter
- 90 posts since 19 Feb, 2005 from uk
the only way i got round it is by downloading midi yoke.it now works a treat.ive run fl for an hour with sync box and 303 connected and timing,s spot on.
[k-v-r-i-s-t-h-e-b-e-s-t]
-
- KVRist
- Topic Starter
- 90 posts since 19 Feb, 2005 from uk
just in case i have problems with my fl could someome connect a midi hardware device to there midi out ,then run fl and see if it will run the midi device.i dont mean midi pulses,i mean clock output.as i am sure i read somewhere that fl doesnt have a clock output.anyone understand????
[k-v-r-i-s-t-h-e-b-e-s-t]
-
- KVRer
- 14 posts since 31 Mar, 2005
I have the same problem. Nuendo can do this just fine. But with FL5 connected to my E-MU sp-12, no luck. perhaps cuz its a demo version?dazzer wrote:just in case i have problems with my fl could someome connect a midi hardware device to there midi out ,then run fl and see if it will run the midi device.i dont mean midi pulses,i mean clock output.as i am sure i read somewhere that fl doesnt have a clock output.anyone understand????
It plays the first note on the e-mu and then stops, while nuendo has no problems at all. quite odd.
-
- KVRer
- 14 posts since 31 Mar, 2005
This is still plaguing me with the new FL6 demo.
FL6 demo, enable midi out, enable master sync, using the midi out from a edirol fa-101 fireware interface into the midi in on my sp12. sp 12 set to slave.
Simply cannot do this successfully, but programs like Nuendo and Cubase can master sync to the sp-12(00) just fine.
Besides resorting to Midiyoke as Dazzer explained, does anyone else have any other suggestions?
FL6 demo, enable midi out, enable master sync, using the midi out from a edirol fa-101 fireware interface into the midi in on my sp12. sp 12 set to slave.
Simply cannot do this successfully, but programs like Nuendo and Cubase can master sync to the sp-12(00) just fine.
Besides resorting to Midiyoke as Dazzer explained, does anyone else have any other suggestions?