KVR Audio

jobromedia · Post by **jobromedia** » Wed Mar 22, 2006 10:47 am

Ah that is a little thing I aded for these who are intrested in reverse delays. Just set the mix so it doesn't let much sound out, and the sound will then start to build up.

MrM · Post by **MrM** » Wed Mar 22, 2006 8:52 pm

The two RFFE sliders, they can't be moved on my machine, is that just me?

All the other sliders work fine.

I had some fun during my initial test, while using the plugin on vocals

It can even sound reverb-like...

Nice.

cptgone · Post by **cptgone** » Wed Mar 22, 2006 8:55 pm

MrM wrote:The two RFFE sliders, they can't be moved

it's in the readme: they're "reserved for future use"

MrM · Post by **MrM** » Wed Mar 22, 2006 9:02 pm

The what?
Oh, the readme...

I did an initial test first; so no reading of helpfiles.
Then I'll read helpfiles and test again...

Just part of my normal test procedure...

(you believe me, right?)

cptgone · Post by **cptgone** » Wed Mar 22, 2006 9:14 pm

MrM wrote:(you believe me, right?)

Do I believe mice from Zwollywood? Of course I do.

It's all jobromedia's fault, he should have added a RTFM slider

MrM · Post by **MrM** » Wed Mar 22, 2006 10:57 pm

Yeah, he also messed up at cel I35 of the primary tab of the XLS...

It reads '=GEMIDDELDE(C35:G35)' or '=AVERAGE(C35:G35)'
and it shoud be (C35:H35)

EDIT; I'm not joking! I'm not mad either, just testing it thoroughly

jobromedia · Post by **jobromedia** » Thu Mar 23, 2006 7:36 am

Hmmmm, Can you give me exact table coordinates of the faulty cell?

Glad you guys are doing such hard tests

Thanks!

MrM · Post by **MrM** » Thu Mar 23, 2006 9:19 am

Like I said cel I - 35 of the primary tab.

jobromedia · Post by **jobromedia** » Thu Mar 23, 2006 9:55 am

Ah I'll check it out and be back with a corrected EXCEL file.

jobromedia · Post by **jobromedia** » Mon Mar 27, 2006 1:38 pm

Apart from the messy xls file are ya having fun?

Allmost decided what the RFFE will be linked to. A bitcrusher connected between the lfo and the delay to make some shaping of the waveform.

Canned Heat · Post by **Canned Heat** » Mon Mar 27, 2006 2:09 pm

jobromedia wrote:Apart from the messy xls file are ya having fun?

Allmost decided what the RFFE will be linked to. A bitcrusher connected between the lfo and the delay to make some shaping of the waveform.

spuddle · Post by **spuddle** » Mon Mar 27, 2006 4:27 pm

Bitcrusher

Great great, I've had to pause my testing for a week because my final project is due in for University but will get back to it soon and finish off my presets as well as record a few little samples for you all.

MrM · Post by **MrM** » Mon Mar 27, 2006 4:48 pm

Testing all the parameters does take some time

jobromedia · Post by **jobromedia** » Mon Mar 27, 2006 5:56 pm

Beta 2 will exclude the excel file, that's for sure. If you find any anomaly then please don't hesitate to post it here so I can get on top of it ASAP.

MrM · Post by **MrM** » Mon Mar 27, 2006 6:04 pm

so far the plugin has been very stable; no problems found yet!
And it sounds cool too

Drunk Delay beta 1