KORE Sound templates for VSTs - consolidated thread

[JonathanDragonDJ]

how exactly do i load a new ksd into kore? i tried to figure out from the manual but i'm lost....also can you explain the process...i wanna make some patches for the non NIsynths i have....
thx

[ew]

All the user content goes in the user sound folder (or folders, if you've added them to your database). The default on a Windows system is Document and Settings/Native Instruments/Shared Content/Sounds (the same location as user content for any of the NI synths; the synths just have subfolders). It's a good idea to have subfolders for each synth (and subfolders of that folder for easy searching).

When you start up KORE, it will scan the user location. Browse to the sound you want and drag it into the performance or sound view.

To make your own, load the plugin from the sound view. Make your controller assignments and select your attributes. Save to your user content location. Done.

ew

[mn]

A little bump to get this back on the radar since Kore 2 was just released

[ew]

OK, Mike- as long as you bumped...

Here's one for VirSyn's CUBE. It's seven pages- two pages for the sources (ensemble, spread, rate and depth for A and B in one, and the same for C and D in the nexxt), three effects pages (distortion, phaser/chorus/flanger and delay- you can't map the reverb parameters), one for the arp and EQ, and the other handling all the rest such as velocity, number of partials, etc.

Basically anything that can be mapped through user pages is. Plus, you get a cool CUBE patch from me to boot

For Kore 2- this won't work in Kore 1.

Get it here

ew

[aMUSEd]

Oh thanks - I forgot about this thread when I posted this:

http://www.kvraudio.com/forum/viewtopic ... light=kore

This has the link to my KORE SynthPack with templates for:

CamelAudio Cameleon
ReFX Claw
GrooveCube Exciton
Foorius
Terratec Komplexer
FXPansion Orca
Virsyn Poseidon
Arturia Prophet V
Rhino 2
Ohmforce Symptohm Melohman
Sytrus 2.5
DiscoDSP Discovery 2 and Vertigo 2
uhe Zebralette

now added:

Virsyn Cube 2
Virsyn Tera 3
ZeroVector
Firebird +

the Virsyn ones are just "easy performance" pages rather than the full set of controls as they have tons - I just picked out what I use the most for instant changes to the sound.

The Firebird + one requires you to also have Wusik Oversampler installed as it uses that to wrap Firebird to get around the problem with KORE not loading FXB's as Kirebird does not have it's own loader for presets. I should probably have done the same for Foorius but you can drag fxb's onto that to load them and that will be less of an issue in KORE 2 anyway so I'll probably change it when it arrives.

[aMUSEd]

Oh EW beat me to it with a Cube one only he's done the full Monty

Cheers EW

[ew]

And another VirSyn one from me; this one for POSEIDON.
Twelve pages mapped in a more logical method; it includes separate pages for each effect and the like.
Virtually anything that can be mapped is.

And once again, you get a cool patch from me to boot

You can get it here.

ew

[aMUSEd]

I've added Zebra 2 to the synthpack now - tricky decision to make about this. Since it's a modular so far I've adopted a one page per module approach but since it has 4 oscs and tons of filters it has taken 10 pages just to model those and since the automatable limit is 8 pages I'm wondering whether it's worth it to continue. Also I still haven't done the Comb filters as each of those would take 2 pages and ideally I'd like to prioritise the 8 most useful controls so I can get them onto one page each but having to think about which ones to use - any suggestions?

http://www.fingermarks.co.uk/music/KORE_Synth_Pack.zip

[aMUSEd]

Added an enhanced one for Zebra 2 with 2 pages per Comb filter, mappings for noise oscs and shapers and some mod knobs also mapped (where there was room to). 18 pages!!

http://www.fingermarks.co.uk/music/Zebra2.ksd

[aMUSEd]

Now 27 pages !!

All the oscs and filters are now mapped to KORE controls inc the FM oscs, COMB and XMF filters - most on 1 or 2 pages apiece. Where possible I've also added in modulation assignments as well. I left out very little but some just don't seem to be assignable such as "Keyscale" and a few other osc functions as well as most buttons.

Download from here:

http://www.fingermarks.co.uk/music/Zebra2.ksd

and I've also added the updated file to the Synthpack now it's finished.

[aMUSEd]

Eric did you ever finish doing one for Tera 3?

[aMUSEd]

I've updated my Tera 3 template for use with Native Instruments KORE 2. The original one was very minimal - just the filters mainly as I found it a bit daunting to attempt the whole synth. I still haven't mapped every single parameter which would extend to many pages but have tried to map the most important ones for usability. It can be downloaded from here:

http://www.fingermarks.co.uk/music/VirsynTera3.zip

I notice Sound import is still broken for Tera though (seems to be working now for Cube at least) but this can at least be used to play it using the KORE hardware.

[ew]

I've updated my Tera 3 template for use with Native Instruments KORE 2. The original one was very minimal - just the filters mainly as I found it a bit daunting to attempt the whole synth. I still haven't mapped every single parameter which would extend to many pages but have tried to map the most important ones for usability. It can be downloaded from here:

http://www.fingermarks.co.uk/music/VirsynTera3.zip

TERA's a beast to map; there's just so many variables. Thanks, Steve...

I notice Sound import is still broken for Tera though (seems to be working now for Cube at least) but this can at least be used to play it using the KORE hardware.

Yeah- that one's a Virsyn issue. Harry's aware of it; it will be fixed in the next update (which might end up being TERA 4 from what I've heard so far).

ew

[aMUSEd]

Sorry please redownload (or fix yourself). For some reason the filter section isn't working properly so I've redone it.

[Chad@PA]

Jumping in here: Rapture KSD

Enjoy!