Actually I forgot that I don't use SSE2 instructions, cause SSE2 is mostly for 64-bit, which I don't belive to be useful for audio. So it will be only SSE1 or SSE3. =)Christian Schüler wrote:Never underestimate the median age of computer systems.
I had to make an SSE-1 compatibility because I was getting complaints from people with Athlon-XP processor. And I think EpicVerb had to react to these complaints too.
New algorithmic Reverb - Mo' Verb
-
- KVRist
- Topic Starter
- 34 posts since 6 Feb, 2008
-
- KVRian
- 687 posts since 27 Dec, 2003
Suggestions:agorka wrote:Any suggestions/ideas are welcome.
1. Hide mouse cursor when dragging the faders too (works fine on knobs already)
2. Make fader movement speed bit slower
3. Add "fine tune" mode via "modifier key + mouse drag"
4. "Limit" the tuning range on the knobs:
-> drag knob to its maximum and don't release the mouse button
-> drag it further "above" this "limit"
-> now drag the fader back
=> Do you see the issue? It should immediately get back from the "maximum" value. The movement above the "maximum" shouldn't get "remembered". Just have a look at the knobs in Voxengo or Ohm Force plugins for example ...
5. Allow mouse wheel tuning on faders too (works fine on knobs already)
6. Disable mouse wheel tuning when out of knob/fader range:
-> hover the mouse over a knob
-> turn mouse wheel
=> fine
-> move mouse away (say over the "RL" logo)
-> turn mouse wheel
=> Now the same know still gets tuned? Shoudln't happen (to avoid accidental movements).
-
- KVRian
- 687 posts since 27 Dec, 2003
No changes in 1.04 ...Dandruff wrote:Suggestions:agorka wrote:Any suggestions/ideas are welcome.
1. Hide mouse cursor when dragging the faders too (works fine on knobs already)
2. Make fader movement speed bit slower
3. Add "fine tune" mode via "modifier key + mouse drag"
4. "Limit" the tuning range on the knobs:
-> drag knob to its maximum and don't release the mouse button
-> drag it further "above" this "limit"
-> now drag the fader back
=> Do you see the issue? It should immediately get back from the "maximum" value. The movement above the "maximum" shouldn't get "remembered". Just have a look at the knobs in Voxengo or Ohm Force plugins for example ...
5. Allow mouse wheel tuning on faders too (works fine on knobs already)
6. Disable mouse wheel tuning when out of knob/fader range:
-> hover the mouse over a knob
-> turn mouse wheel
=> fine
-> move mouse away (say over the "RL" logo)
-> turn mouse wheel
=> Now the same know still gets tuned? Shoudln't happen (to avoid accidental movements).
-
- KVRian
- 1305 posts since 26 May, 2003 from im müscha...
...thx-
- KVRist
- Topic Starter
- 34 posts since 6 Feb, 2008
Thanks for suggestions! I wasn't visiting this thread for a while, so I didn't knew about your suggestions! I'll do what I'm able to soon!Dandruff wrote:Suggestions:agorka wrote:Any suggestions/ideas are welcome.
-
- KVRAF
- 1770 posts since 30 Jul, 2007
IMO, this kicks EOS's ass across the floor and off a cliff. 
Thank you. I wish your Twin Delay had as nice of a GUI as this one.
Keep up the good work... you have something good going here with the Mo'Verb
Thank you. I wish your Twin Delay had as nice of a GUI as this one.
Keep up the good work... you have something good going here with the Mo'Verb
-
AstralExistence AstralExistence https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=265049
- KVRAF
- 2276 posts since 19 Sep, 2011
does itvaisnava wrote:IMO, this kicks EOS's ass across the floor and off a cliff.
Thank you. I wish your Twin Delay had as nice of a GUI as this one.
Keep up the good work... you have something good going here with the Mo'Verb
-
- KVRAF
- 1770 posts since 30 Jul, 2007
RL,
One suggestion... an Windows x64 version for future compatibility.
One suggestion... an Windows x64 version for future compatibility.
-
- KVRAF
- 14304 posts since 20 Nov, 2003 from Lost and Spaced
Love both.. The Twin Delay preset 'Dubwise' is aces. I think you're a genius.