KVR Audio

umd · Post by **umd** » Tue Mar 09, 2010 8:47 am

Hi.

Is it the normal version or the 16 or 8 out version of K4?

Can you send me a test project that I can open with K4 player?

standalone · Post by **standalone** » Thu Mar 11, 2010 4:52 pm

Hey!, I bring a brand new opcode to the party. "Dispatcher opcode 19 failed".

It only happens in Kontakt 3.5 (XP32, Cubase 4), and only when I load some very big instruments (around 1GB) that come with loads and loads of scripting (this seems to be the key, as other equally big instruments don't trigger this).

Truth is that, after clicking "accept", everything finish loading normally and the instument and Kontakt seem to work fine, so it's just the warning that I'm experiencing.

umd · Post by **umd** » Thu Mar 11, 2010 4:55 pm

Hello.

Is it with Cubase5?

If yes, please email me with your user details and I'll send you a test version, I've been working on that issue.

standalone · Post by **standalone** » Thu Mar 11, 2010 5:03 pm

No, Cubase 4.

umd · Post by **umd** » Thu Mar 11, 2010 5:04 pm

Ok, it could work as well, I've had this reported before but with Cubase5. Drop me a line, I have something for you to try.

Thanks

standalone · Post by **standalone** » Thu Mar 11, 2010 5:08 pm

Pinnsvein · Post by **Pinnsvein** » Mon Mar 15, 2010 4:00 pm

standalone wrote:OK!.

Isn't Kontakt 4 64bit already? I run it in Cubase 5 on Windows 7 without any problem...

standalone · Post by **standalone** » Mon Mar 15, 2010 5:36 pm

Pinnsvein wrote:
standalone wrote:OK!.
Isn't Kontakt 4 64bit already? I run it in Cubase 5 on Windows 7 without any problem...

I run Jbridge in a 32 bit enviroment to overcome the host's 2GB of ram limit. The problem that I had (it has been adressed by the version that umd sent me) affected only very complex Kontakt's instruments.

Pinnsvein · Post by **Pinnsvein** » Mon Mar 15, 2010 6:06 pm

How do I point my host (Cubase in my case) to the JBridge folder? Is this done under preferences or do I use the scan function

standalone · Post by **standalone** » Mon Mar 15, 2010 6:11 pm

Pinnsvein wrote:How do I point my host (Cubase in my case) to the JBridge folder? Is this done under preferences or do I use the scan function

Move the plugins to another location out of the host's view and point Jbridge to put the "fake" bridged versions in their place.

Pinnsvein · Post by **Pinnsvein** » Tue Mar 16, 2010 8:49 am

I must be doing something wrong here...
I moved the original .dll files in the vst folder to another location and then I ran Jbridge again, directing the program to put the bridged versions into this folder. They did not show up there but on another location I created before instead. I tried to move them manually but Cubase did not recognize them. Do I need to rescan something?

Pinnsvein · Post by **Pinnsvein** » Tue Mar 16, 2010 9:41 am

Now I found something but the issue is that Cubase reads my Jbridged instruments as effects instead of VST instruments. How do I change this?

umd · Post by **umd** » Tue Mar 16, 2010 10:29 am

Hi.

Please make sure that Cubase is not also scanning the folder where the original .dll files are. Check the plugin scan paths to be sure.

Regarding the instruments recognized as fx's, try renaming the created .64.dll/64.txt files to .dll/.txt and re-scan them.

Pinnsvein · Post by **Pinnsvein** » Tue Mar 16, 2010 11:26 am

Tried to rename them and got the following messages: "This buffer already exists" and "This semaphore already exists"...

Pinnsvein · Post by **Pinnsvein** » Tue Mar 16, 2010 11:27 am

...and ML semaphore open error 2

Need testers for my x86 to x64 vst adapter