KVR Audio

Mister Natural · Post by **Mister Natural** » Sun Apr 10, 2011 7:11 pm

whoa . . .

thanks Arto - playing with this plug this morning was too much fun

Can't wait to play more deeply with programming here

respect

Karmacomposer · Post by **Karmacomposer** » Sun Apr 10, 2011 10:08 pm

Very nice. How does this compare to Sugar Bytes Consequence?

Mike

Arde2 · Post by **Arde2** » Tue Apr 12, 2011 6:25 pm

I case you haven't noticed: There is actually AU version available on Kirnu web page.

There is some info how to get it to work with Logic in Thesys Manual section 'The Logic AU Workaround'. Thanks Sugar Bytes!

Please tell me how it works for you.

- Arto

cosmosis · Post by **cosmosis** » Wed Apr 13, 2011 2:18 am

Wow, how did I miss out on this one? I was recently thinking that the world needed a good freeware arpeggiator. This is it

Arde2 · Post by **Arde2** » Wed Apr 13, 2011 6:05 pm

'The Logic AU Workaround' doesn't work because Kirnu's output needs to be connected to IAC bus directly. I'll try to sort this out.

Also there is a looping behaviour fix for Presonus Studio One which I have sorted out but I think I found a bug from there and I want to sort that out also before releasing a new version.

- Arto

b-pole · Post by **b-pole** » Wed Apr 13, 2011 6:25 pm

The Logic AU Workaround' doesn't work because Kirnu's output needs to be connected to IAC bus directly. I'll try to sort this out.

Still hoping it will work soon.

Echoes in the Attic · Mon Apr 18, 2011 11:47 pm

Been playing around with it and I'm finding that it often leaves a short gap when I change chords, even though I am careful to overlap the pressed notes. I can't figure out exactly why it does, but it doesn't seem to happen using the Kore arp or ableton's arp.

Any ideas? I've tried different settings and can't change chords held while having continuous play, it always loses a note.

cheers

tomtoo · Post by **tomtoo** » Tue Apr 19, 2011 2:47 pm

Hi all,

i did a little vid how to use and route kirnu in energyXT 2.5 .(For beginners)

Thanks a lot for Kirnu !

Greatings
Thomas

Arde2 · Post by **Arde2** » Wed Apr 20, 2011 7:55 pm

Thanks Thomas. Nice video. Thanks for doing that.
Can I include it on my Kirnu media page?

- Arto

Echoes in the Attic · Post by **Echoes in the Attic** » Wed Apr 20, 2011 8:00 pm

Any thoughts on the notes dropping out?

Arde2 · Post by **Arde2** » Wed Apr 20, 2011 8:35 pm

Could you be more specific about the case when the notes drop out. And what does that dropping out mean? Aren't those notes played at all?

You could record MIDI while playing and send that file to me with explanation how Kirnu should play it and I'd try to fix the problem.

I have noticed that when using chords Kirnu ignores notes for couple of steps if the rate is big because the notes don't come to plugin at the same time if you are playing manually.

- Arto

tomtoo · Post by **tomtoo** » Thu Apr 21, 2011 10:03 am

Arde2 wrote:Thanks Thomas. Nice video. Thanks for doing that.
Can I include it on my Kirnu media page?

- Arto

Hi Arto ,

shure you MUST !

Greatings and again thanks for this great tool !
Thomas

Virtuos1 · Post by **Virtuos1** » Wed May 04, 2011 4:09 pm

Any news about using Kirnu with Logic?

D N A · Post by **D N A** » Wed May 04, 2011 5:31 pm

Just spreaded the info about Kirnu

http://www.vstcafe.com/2011/05/kirnu-mi ... lugin.html

Hope to bring you more hmm fame and downloads

Arde2 · Post by **Arde2** » Fri May 06, 2011 10:11 am

Virtuos1 wrote:Any news about using Kirnu with Logic?

I have an experimental version of Kirnu ready which can be used in Logic.
This version uses IAC buses to move MIDI data between Kirnu and Logic.
The version is very unstable though and I don't know if this hack would be good solution even if it worked without crashes because of the latency issues.

- Arto

Kirnu - The Arpeggiator v1.1 released (x64,SSE,Mac OS X)