KVR Audio

nix808 · Post by **nix808** » Thu Nov 22, 2012 12:11 pm

OK-sorry-there was a really bad graphics bug that used a CPU.
You can redownload in the original post

Teksonik · Post by **Teksonik** » Thu Nov 22, 2012 12:24 pm

Thanks for this plugin, I hadn't seen this thread until now. I'll give it a try after our Thanksgiving feast later today.

Is it just me or are the input/outputs on the wrong sides (not that it matters)?

nix808 · Post by **nix808** » Thu Nov 22, 2012 12:59 pm

no worries-
very welcome.
The way the input and output is,
it's the same as a stompbox.
Hope it doesn't cause indigestion! 8D
Sounding alright over synth atm,
but you have to sequence a little late.
Will look into PDC.
hmm-just1500pdc should work

Hope you are having a sweet one,
and happy returns

nix808 · Post by **nix808** » Tue Jan 29, 2013 7:05 am

OK-I stopped it crashing.
I will make 3 versions of this,
as I have 3 algos.
This is version 1,
the algo is linear interpolated reasampling of float arrays.
The ends are faded together.
It's basically my own design,
but the heavy lifting is by Outsim.

Thanks to Marc Schlaile @ Access for the props on the GUI.
The GUI is the RedLight one.
Cheers-
btw If you try it let me know if it's cool or cr@ppy 8D
It remains 1500 samples PDC I think

64-bit will be available as soon as SynthMaker implements it

nix808 · Post by **nix808** » Wed Jan 30, 2013 11:34 am

OK, hey again--
IMO, todays work on this was sweet.
I stopped it popping when u change the pitch.
MIDI learn is working too.
However, automation is still pretty much unsupported.
Anyway- I think it's cool.
Will try get automation up tomorrow--
it's something to do with VST spec being all parameters at 0-1,
hmm
If you'd like to use a controller-
click the little MIDI plug in the right corner,
select source.
Right click the pitch slider and move the physical knob.
It will learn.
It's possible to change the pitch when recordsing now,
as the pop or crackle on change is gone.
Cheers- please check in to my upcoming stuff if it it suits 8D

nix808 · Post by **nix808** » Thu Jan 31, 2013 2:23 am

http://www.sendspace.com/pro/dl/aszp28

changelog--
automation works, ignore the parameters that start with z
resolution is 1 cent, not 2 cents

This is a version 1 perhaps
Cheers!

edit-I have updated the d/l again,
I conserved a lot of graphics CPU

nix808 · Post by **nix808** » Tue Feb 05, 2013 10:39 am

a bump for my most finished plug ever!
8D

Here is a quick rundown on the controls:-
The slider on the right selects which line you are setting the shift for.
The 3 sliders on left are-
1 2 3
octave semitone cents

The arrow button sets parralel or serial.

The little ableton -style knobs are the mix amps
for each line, or main volume in serial mode.

The LEDS switch each line on or off.

It certainly shouldn't make noise.
The shifted sound should come through nicely, with a slight vibrato,
because of the grain smoothing.

The red MIDI plug sets the controller, right click on control enables MIDI learn.
The 'x' that is visible after opening the learn dialogue is unlearn.

It doesn't stretch,
but you can stretch with sampler's pitch,
and then compensate with this, so that it doesn't change the sample's
original pitch. Good for mixing loops which have been cut at various BPM.

Cheers 8D

nix808 · Post by **nix808** » Wed Feb 13, 2013 4:51 am

Just upping this again.
Not many downloads,
but thanks to those who give it a burl.
My developments are getting better IMO

VariKusBrainZ · Post by **VariKusBrainZ** » Wed Feb 13, 2013 1:42 pm

nix808 wrote:Just upping this again.
Not many downloads,
but thanks to those who give it a burl.
My developments are getting better IMO

Where can be get the current version?
Rekkerd appears to only have v1?

chuck death · Post by **chuck death** » Wed Feb 13, 2013 2:02 pm

VariKusBrainZ wrote:
nix808 wrote:Just upping this again.
Not many downloads,
but thanks to those who give it a burl.
My developments are getting better IMO
Where can be get the current version?
Rekkerd appears to only have v1?

3 posts above your question is the sendspace link.

nix808 · Post by **nix808** » Thu Feb 14, 2013 4:34 am

Yep- all the links in this thread are for the current one.
I fixed that iterations on the slider graphics,
but it's so minor GUI change only.
Sorry about the state of the Rekkerd site,
I think I've said to Ronnie(Core) twice that I will up the new stuff,
but it's still not quite ready for a big overhaul.
I want to do a good job finalizing everything.
Cheers 8D

nix808 · Post by **nix808** » Thu Feb 28, 2013 7:29 am

I was let know there was a problem with distorsion when shifting beyond 1 octave up. It's fixed now. Also automation parameters are all relevant and correct. The trigger is also less complicated, looks good on cpu here.
Here it is->
http://www.sendspace.com/pro/dl/aszp28
Sorry for all my faulted releases, if you bear with me, I will make good 8D

Shifter_resample--new tech from Phonics, enabled by Flowstone