KVR Audio

jacobh · Post by **jacobh** » Fri Mar 10, 2017 4:01 am

Anyone know if it's possible to control the Resolution of the Step Line or Arpeggiator with a modulation source?

Thanks!
Jacob

maximoog · Post by **maximoog** » Fri Mar 10, 2017 4:47 pm

Feature request: Switch off the loop function in the stepenvelope:

I use the step envelope for wavesequencing and wants to create occasional sequences that are only once played. Is it possible to install a stop function in the step envelope?

otristan · Post by **otristan** » Fri Mar 10, 2017 4:58 pm

jacobh wrote:Anyone know if it's possible to control the Resolution of the Step Line or Arpeggiator with a modulation source?

Nop.

EvilDragon · Post by **EvilDragon** » Fri Mar 10, 2017 4:58 pm

Would be great to be able to toggle looping of the step envelope. It could be another entry in the Retrigger dropdown - oneshot

otristan · Post by **otristan** » Fri Mar 10, 2017 4:59 pm

maximoog wrote:Feature request: Switch off the loop function in the stepenvelope:

I use the step envelope for wavesequencing and wants to create occasional sequences that are only once played. Is it possible to install a stop function in the step envelope?

Not possible right now, but you can easily achieve the same thing using the multi envelope which allows to not have looping.

maximoog · Post by **maximoog** » Sat Mar 11, 2017 10:50 am

otristan wrote:
maximoog wrote:Feature request: Switch off the loop function in the stepenvelope:

I use the step envelope for wavesequencing and wants to create occasional sequences that are only once played. Is it possible to install a stop function in the step envelope?
Not possible right now, but you can easily achieve the same thing using the multi envelope which allows to not have looping.

Thank you. I will try it.

Wavegem · Post by **Wavegem** » Mon Mar 13, 2017 12:49 pm

I am in the process of building a complex patch. Currently 350 key groups, macro is fully loaded. The problem is when I add another part and load a second instance of the same patch I get no response from the macros. It’s like none of my assignments are there and just plays the default sound. When I open another instance of falcon and load that patch everything is fine. I tried the same thing on another computer with the same results

Wavegem · Post by **Wavegem** » Mon Mar 13, 2017 4:33 pm

Edit
Trying to figure this out I noticed that only a few macros aren't responsive. In particular I mapped ON/OFF sample osc modulation to a macro w/mod envelope which rotates between the different sample osc keygroups. Also I lose all adsr macro modulation . What's weird is that I have thorus ON/OFF macro which works but the delay ON/OFF macro , feedback and timing doesn't. The compressor has control and portamento does . Arpegiator ON/OFF doesn't work but the step sequencer ON/OFF Does as well as the speed. I check all the mappings and it says it's assigned and when I rotate the value knob at the bottom right corner it works just not the macro

EvilDragon · Post by **EvilDragon** » Tue Mar 14, 2017 8:51 am

I'd suggest packing that patch up and sending it to UVI support

otristan · Post by **otristan** » Tue Mar 14, 2017 9:06 am

Yep, this would be the only way to debug this.

Dúnedain · Post by **Dúnedain** » Wed Mar 15, 2017 8:17 pm

Check this out. You can map keys to parameters in Falcon with the Mapper Editor. I used this to give each key its own unique filter cut off frequency. Useful for recreating the sound of other synths up to the harmonic.

EvilDragon · Post by **EvilDragon** » Wed Mar 15, 2017 9:11 pm

Yep, modmapper can be used in all sorts of ways.

RobGee · Post by **RobGee** » Sun Mar 19, 2017 2:55 am

Any chance of getting more trigger modes added such as the ones listed below? Unless i'm missing something and someone can point out a way of currently setting these up in Falcon. I use these a lot with my Emu samplers, would be great to have something similar in Falcon.

Sampleconstruct · Post by **Sampleconstruct** » Sun Mar 26, 2017 4:48 am

FYI: yesterday I released another sample- and sound library from my Falcon Singles-series, the HANG (pentatonic percussion instrument), check it out here.

_TIP_ · Post by **_TIP_** » Fri Apr 28, 2017 1:11 pm

So, does anyone know if Falcon is still under development, are we going to see any exciting updates any time soon?
Thanks!

UVI Falcon - v4 = 2026 released - rumors, ads, praise, kindergarden, auto-sampling and off-topic inside!