KVR Audio

an-electric-heart · Post by **an-electric-heart** » Wed Dec 18, 2019 12:26 am

I haven't been able to get the site to load... but as others have said; There's plenty of time. I just want to know what sort of copy protection it uses. Is it ilok like their other stuff?

simmo75 · Post by **simmo75** » Wed Dec 18, 2019 12:29 am

an-electric-heart wrote: Wed Dec 18, 2019 12:26 am I haven't been able to get the site to load... but as others have said; There's plenty of time. I just want to know what sort of copy protection it uses. Is it ilok like their other stuff?

None of their products are iLok.

an-electric-heart · Post by **an-electric-heart** » Wed Dec 18, 2019 12:42 am

simmo75 wrote: Wed Dec 18, 2019 12:29 am
an-electric-heart wrote: Wed Dec 18, 2019 12:26 am I haven't been able to get the site to load... but as others have said; There's plenty of time. I just want to know what sort of copy protection it uses. Is it ilok like their other stuff?

None of their products are iLok.

Oh right, doh

. I don't actually have any of their products... I just thought they were... I don't care, I've got an ilok.

Lesha · Post by **Lesha** » Wed Dec 18, 2019 1:01 am

Nice one, thanks Arturia!

foosnark · Post by **foosnark** » Wed Dec 18, 2019 1:25 am

mholloway wrote: Wed Dec 18, 2019 12:16 am
foosnark wrote: Tue Dec 17, 2019 11:35 pm The website's not working for me, but Arturia Software Center started up fine. I successfully installed Rev Plate-140 and updated Easel with no trouble at all.

When I load up and run the Software Center, there is no sign of the new reverb anywhere, so I'm not sure how you actually managed to get it this way.

Hmm, maybe my attempt to log in through their website worked, even though it looked on my end like it timed out.

Sindikhate · Post by **Sindikhate** » Wed Dec 18, 2019 1:42 am

I got the NI earlier in the morning, this takes ages to load the website. Still a week to go though.

Echoes in the Attic · Post by **Echoes in the Attic** » Wed Dec 18, 2019 2:04 am

Wow, second free reverb this christmas!

cthonophonic · Post by **cthonophonic** » Wed Dec 18, 2019 2:36 am

Looks like Arturia was so generous they gave me two licenses, so second *and* third free reverb for me!

Russell Grand · Post by **Russell Grand** » Wed Dec 18, 2019 2:57 am

Ridiculous.

mholloway · Post by **mholloway** » Wed Dec 18, 2019 3:03 am

foosnark wrote: Wed Dec 18, 2019 1:25 am
mholloway wrote: Wed Dec 18, 2019 12:16 am
foosnark wrote: Tue Dec 17, 2019 11:35 pm The website's not working for me, but Arturia Software Center started up fine. I successfully installed Rev Plate-140 and updated Easel with no trouble at all.

When I load up and run the Software Center, there is no sign of the new reverb anywhere, so I'm not sure how you actually managed to get it this way.
Hmm, maybe my attempt to log in through their website worked, even though it looked on my end like it timed out.

Actually, I just found it -- it's under the 'Explore Products' section of the software center, all good.

Russell Grand · Post by **Russell Grand** » Wed Dec 18, 2019 4:02 am

I can vouch for skipping Arturia's overloaded website altogether and just going through Software Center and activating. Works like a charm.

thecontrolcentre · Post by **thecontrolcentre** » Wed Dec 18, 2019 4:42 am

I got it using the software centre, but I cant get onto the site to register, so its demo mode only for now. I like this one and the NI one. Was much easier to install the NI verb ... I wasn't given any option about where to install the vst2 by Arturia. I found it in the same location as my last install of MiniFilter. No worries tho ... its very generous of both companies. Will try to register rev plate again tomorrow.

mholloway · Post by **mholloway** » Wed Dec 18, 2019 4:55 am

thecontrolcentre wrote: Wed Dec 18, 2019 4:42 am I got it using the software centre, but I cant get onto the site to register, so its demo mode only for now. I like this one and the NI one. Was much easier to install the NI verb ... I wasn't given any option about where to install the vst2 by Arturia. I found it in the same location as my last install of MiniFilter. No worries tho ... its very generous of both companies. Will try to register rev plate again tomorrow.

There is no 'demo' mode for this, and no license or serial or anything. It's a true freebie. If you have it, you have it, no registration needed.

plexuss · Post by **plexuss** » Wed Dec 18, 2019 4:56 am

Strange, I don't see an instlaler in the Arturia Software Center. I was able to eventually get it into my account via the site after refreshing the page multiple times and it eventually loading. Then I see it in the SW Center as activated. I see no way to install it from the SW Center. Do you?

mholloway · Post by **mholloway** » Wed Dec 18, 2019 4:57 am

plexuss wrote: Wed Dec 18, 2019 4:56 am Strange, I don't see an instlaler in the Arturia Software Center. I was able to eventually get it into my account via the site after refreshing the page multiple times and it eventually loading. Then I see it in the SW Center as activated. I see no way to install it from the SW Center. Do you?

When I clicked the "explore products" tab in the software center, the plate reverb was located in there, with an install button next to it. I had not done anything on the website prior to that (it wasn't even loading).

Arturia Xmas Gift Reverb PLATE-140