KVR Audio

SJ_Digriz · Post by **SJ_Digriz** » Wed Dec 16, 2020 3:51 pm

ShawnMH wrote: Wed Dec 16, 2020 3:41 pm
SJ_Digriz wrote: Wed Dec 16, 2020 3:32 pm One of my SVXs just showed up, so it's just lag. I also have Metal now and I never purchased that
Is stand alone version working for you yet?

I haven't retried. Been messing about in DAW insert mode.

revvy · Post by **revvy** » Wed Dec 16, 2020 3:53 pm

SJ_Digriz wrote: Wed Dec 16, 2020 3:50 pm
revvy wrote: Wed Dec 16, 2020 3:24 pm Is there a way to do it from within AT?
There is a custom shop button on the top right of the interface. I am using that from within a Cubase instace.

Got it.

My Ampeg is now showing up in CS but not in AT. I'll be patient but I'm a bassist, gimme back my main packs!

donkey tugger · Post by **donkey tugger** » Wed Dec 16, 2020 3:57 pm

Good stuff. Always thought that AT did the metel/rokk stuff well, but it always disappointed me on the question of prime importance -i.e. can it do the jangle properly, with the correct amount of chiming and fizz?

Nice now. Tried the Copper amp thingy, and it made the Shitenbacker Mk1 12 string sound like a million dollars (ok, like £200 rather than the £100 I paid for it...).

That sorted, I shall plug in one of my (ahem..) 'rock axes' later on for a bit of chug and widdle (easy now...) action.

vurt · Post by **vurt** » Wed Dec 16, 2020 3:58 pm

J4R1O wrote: Wed Dec 16, 2020 3:42 pm Jimi Hendrix showed up

pretty sure it wasn't really him...

donkey tugger · Post by **donkey tugger** » Wed Dec 16, 2020 3:58 pm

SJ_Digriz wrote: Wed Dec 16, 2020 3:32 pm I also have Metal now

You'll never be METEL

SJ_Digriz · Post by **SJ_Digriz** » Wed Dec 16, 2020 4:16 pm

donkey tugger wrote: Wed Dec 16, 2020 3:58 pm
SJ_Digriz wrote: Wed Dec 16, 2020 3:32 pm I also have Metal now
You'll never be METEL

I don't have enough tatoos and I shower far too often.

SLiC · Post by **SLiC** » Wed Dec 16, 2020 4:17 pm

Initial thoughts after 30 minutes....this is pretty damn good!
Sounds great, lovely resizable interface and I can hide stuff I don't own easily.

However....they really need to make the 'hide gear I don't own' button remember the selection (or put it in preferences) so they I don't have to press it every single time I load A5

phil.harmoniq · Post by **phil.harmoniq** » Wed Dec 16, 2020 4:23 pm

First impressions are good, but as far as I can tell MIDI seems to be broken when using in Ableton. I can control Amplitube 4 just fine with my foot pedal controller but 5 doesn't detect anything.

Edit: The issue seems to only affect the VST3 version

dven · Post by **dven** » Wed Dec 16, 2020 4:32 pm

Same issue with some gear pieces not unlocking in AT5 (example Orange Tiny Terror). Shows as unlocked in AT4, but not in AT5. Will wait some and then try the restore gear from custom shop again.

Teksonik · Post by **Teksonik** » Wed Dec 16, 2020 4:35 pm

And here we go.....

Installed the Product Manager on my test computer and got this:

IK 121620-1.png

The Product Manager and AT 5 CS seem to be functioning but no Custom Shop.

Then when loading AT 5 CS for the first time I got the following expected message but clicking on OK did not open the PM. Perhaps that's because of the above error.

IK 121620-3.png

After installing the PM and AT 5CS I got this:

IK 121620-2.png

It's just a product manager and a single plugin so not sure why IK needs to get its hooks so far in to our systems that a reboot is required.

So meh I'm not going to bother installing AT5 on my studio computer. I'll just leave my TRacks5, Sampletank, and Syntronik installs intact on the old license manager at least until there is a good reason to install the new Product Manager. So I'm out.......

SJ_Digriz · Post by **SJ_Digriz** » Wed Dec 16, 2020 4:39 pm

stand alone is still no go. Just doesn't pass audio at all. I tried windows and direct, but it simply doesn't sync up. I also get the connection dialog every time i open stand alone even though the values are set. So it seems it doesn't think it is setup even though it is.

gathda · Post by **gathda** » Wed Dec 16, 2020 4:42 pm

Registration is working for me now.

telecode · Post by **telecode** » Wed Dec 16, 2020 4:47 pm

My impressions thus far. The resizable GUI is great. It has not translated well for the Fulltone collection which I use a lot.

The new racks setup I am not a fan of either. It looks like Mixbox -- nothing is horizontal anymore. (Maybe I need to get used to it.) I am also finding weird limitations in SE version. I need to confirm they are limitations and not just that I am not seeing the obvious settings that needs to get clicked as the GUI had changed a lot since AT 4.

I still need to play around with it some more.

SJ_Digriz · Post by **SJ_Digriz** » Wed Dec 16, 2020 4:55 pm

telecode wrote: Wed Dec 16, 2020 4:47 pm The new racks setup I am not a fan of. It looks like Mixbox -- nothing is horizontal.

I'm not sure what you mean here. It has a summing mixer that looks mixbox. But it has racks before and after that mixer that look like ST4 "500" format boxes. It's completely horizontal instead of the old vertical.

minkray · Post by **minkray** » Wed Dec 16, 2020 5:03 pm

The resizable GUI is great. It has not translated well for the Fulltone collection which I use a lot.

does it have the blurry gui issue MixBox had upon release?

Amplitube5 - Release Date 15-16/12/2020