KVR Audio

jens · Post by **jens** » Sun Apr 04, 2021 12:02 pm

Amazing synth - that's really right up my alley - gives very (conventionally) musical results in an instant - it's super rewarding - it reminds me to some extent of my beloved (but sold) Z1...

now I really need to get a Sensel!

ReverendLove · Post by **ReverendLove** » Sun Apr 04, 2021 12:33 pm

jens wrote: Sun Apr 04, 2021 11:29 am I just got this (for 19USD) and it seems surprisingly great to me - BUT:

I may be very thick and daft, but how on earth do you create/control key-scaling? I didn't find anything in the manual.

Edit:

found the MIDI input - most of it is hidden by default - so that should be N then, right?

2nd edit: yes, that's much better!

You have to use the "V" connector of the modulator "Midi In" (The little keyboard). Connect it to master volume, filter frequency, LFO speed or whatever you want. Yeah, and - read TFM.

jens · Post by **jens** » Sun Apr 04, 2021 1:46 pm

The V would rather be velocity though, right? What I looked for was key-scaling which is the N instead, as I mentioned above.

ReverendLove · Post by **ReverendLove** » Sun Apr 04, 2021 4:58 pm

Yes, you sorted it. It is like a Midi note to cv Converter with a range from 0 - 1

jens · Post by **jens** » Sun Apr 04, 2021 7:37 pm

-1 to +1, right?

ReverendLove · Post by **ReverendLove** » Sun Apr 04, 2021 10:17 pm

jens wrote: Sun Apr 04, 2021 7:37 pm -1 to +1, right?

No, not for pitch. From the manual:
" N: Note number. This will output a 0.0 for MIDI note 0, and 1.0 for MIDI note 127. This is useful for, say, mapping thefilter’s cutoff to the current note"

jens · Post by **jens** » Mon Apr 05, 2021 12:06 am

Yeah, but if you drag it down from the middle it'll still be negative (and that would be quite a lack of function otherwise, right?) - the manual seems a bit incomplete there...

ReverendLove · Post by **ReverendLove** » Mon Apr 05, 2021 10:08 am

Ah, I see. The rulers below the connector, I consider them more as relative position or offset to the value of the target, a simple transfer like Note/128 • Amount + Npos while npos' range goes from 0 to -Amount at the bottom.
Well, this isn't explained in the manual.

jens · Post by **jens** » Mon Apr 05, 2021 10:51 am

Yes, actually you're right - it's basically an offset of a value between 0 and +1

My bad - my thinking was flawed there...

waltercruz · Post by **waltercruz** » Sat Apr 24, 2021 4:14 am

New version with MTS-ESP support.

Version 1.3.0 (Apr 23, 2021)
-Fixed a bug where saved projects in some DAWs would reset both oscillators on load
-Fixed preset name always showing "Default" on project load.
-Added Oddsound MTS-ESP tuning support

WasteLand · Post by **WasteLand** » Sat Apr 24, 2021 7:32 am

waltercruz wrote: Sat Apr 24, 2021 4:14 am New version with MTS-ESP support.

Version 1.3.0 (Apr 23, 2021)
-Fixed a bug where saved projects in some DAWs would reset both oscillators on load
-Fixed preset name always showing "Default" on project load.
-Added Oddsound MTS-ESP tuning support

via PA or unfiltered audio?

EDIT: isn't on the PA page of LION nor on the BETA page of Unfiltered Audio.

so where is it?? where is the fish?

BeeDog · Post by **BeeDog** » Sat Apr 24, 2021 8:35 am

If you reinstall it using the PA Manager, it updates Lion to 1.3.0.

mountainmaster · Post by **mountainmaster** » Sat Apr 24, 2021 10:17 am

WasteLand wrote: Sat Apr 24, 2021 7:32 am
waltercruz wrote: Sat Apr 24, 2021 4:14 am New version with MTS-ESP support.

Version 1.3.0 (Apr 23, 2021)
-Fixed a bug where saved projects in some DAWs would reset both oscillators on load
-Fixed preset name always showing "Default" on project load.
-Added Oddsound MTS-ESP tuning support
via PA or unfiltered audio?

EDIT: isn't on the PA page of LION nor on the BETA page of Unfiltered Audio.

so where is it?? where is the fish?

It is on PA now.

WasteLand · Post by **WasteLand** » Sat Apr 24, 2021 1:05 pm

mountainmaster wrote: Sat Apr 24, 2021 10:17 am
WasteLand wrote: Sat Apr 24, 2021 7:32 am
waltercruz wrote: Sat Apr 24, 2021 4:14 am New version with MTS-ESP support.

Version 1.3.0 (Apr 23, 2021)
-Fixed a bug where saved projects in some DAWs would reset both oscillators on load
-Fixed preset name always showing "Default" on project load.
-Added Oddsound MTS-ESP tuning support
via PA or unfiltered audio?

EDIT: isn't on the PA page of LION nor on the BETA page of Unfiltered Audio.

so where is it?? where is the fish?
It is on PA now.

thanks!! (and other UA products suffered from the same problem it seems, or similar.. o well, i will check!)

D Halgren · Post by **D Halgren** » Sat Apr 24, 2021 3:05 pm

WasteLand wrote: Sat Apr 24, 2021 1:05 pm
mountainmaster wrote: Sat Apr 24, 2021 10:17 am
WasteLand wrote: Sat Apr 24, 2021 7:32 am
waltercruz wrote: Sat Apr 24, 2021 4:14 am New version with MTS-ESP support.

Version 1.3.0 (Apr 23, 2021)
-Fixed a bug where saved projects in some DAWs would reset both oscillators on load
-Fixed preset name always showing "Default" on project load.
-Added Oddsound MTS-ESP tuning support
via PA or unfiltered audio?

EDIT: isn't on the PA page of LION nor on the BETA page of Unfiltered Audio.

so where is it?? where is the fish?
It is on PA now.
thanks!! (and other UA products suffered from the same problem it seems, or similar.. o well, i will check!)

Yep, still waiting for the same 'Default' fix for Triad.

Unfiltered Audio Lion