Zebra 3 Teething Troubles

[eclipse_soundlab]

Another ones. (see: attachments)

Nothing hard to fix (pull one dot and its gone)

BTW Waveform/MSEG editor should have dobule click to change sub-tool type.

Let's say toggle between global and free select mode.

i can't set mseg loop to 1.5 it's either 1.49 or 1.51

I just tried and had no trouble setting loop speed to 1.50 (also can do 1.49 and 1.51)

Maybe double click the knob to reset it. Or you can hold shift for fine adjustment.

yes, nothing works, even key control mode and adjusting with +/-
I dont mind it for now anyway still doing drafts and assets.

[OdoSendaidokai]

I've discovered something really strange again involving Bitwig, Driven By Moss Generic Flexi, the Arturia Minilab 3, and the Zebra3, and I'm not quite sure where the problem lies.

I'm using the Arturia Minilab 3 together with Driven By Moss's Generic Flexi and its endless rotary knobs to control the parameter pages of the devices/plugins. This works flawlessly almost everywhere, BUT with the Zebra3 and the Unison Voices setting, I can’t change this value using knob 2. On all other parameter pages, knob 2 works perfectly.

It also works with the Push2s continuous knobs. However, there is a special Push2 script from DbM.
When I use the Korg nanoKontrol2’s fader with Generic Flexi, the control of this parameter page knob works flawlessly. The same applies to Generic Flexi when I control it with the Novation Impulse Controller.

The only difference I can see is that the Arturia has a continuous knob, while the others have 0–127 faders. However, I don’t have any other controllers with continuous knobs. Do you have any other ideas about what this might be?

02_temp.png

01_temp.png

.
.
.
Here the configuration of the Generic Flexi Script and the Midi CC that is send by the knob.
.
.

03_temp.png

[tasmaniandevil]

When I use an MPE controller, the timbre modulation (piped to Control A) is jagged / there's significant aliasing. It does not seem to vary under different slew rates. When I automate Control A directly, it's smooth.

While we are smoothing MIDI signals, we can’t smooth Bitwig’s Note Expression signals. One possible solution would be to use the Slew option in the mod matrix modifier section. I’ve sent you a more detailed reply through our support system.

[tasmaniandevil]

But they stop working for the ABCD controls. Restarting Logic does not make a difference, creating a new project also not. But restarting the Mac does.

Can you contact our support regarding the control ABCD issue?

[joradn]

When the filter menu is open, clicking another filter to focus it doesn't switch the menu as expected.

In the example, I've opened the menu for filter 2, then clicked on filter 1, but the menu remains on filter 2. I would expect it to either change to filter 1, or to close.

[pdxindy]

When the filter menu is open, clicking another filter to focus it doesn't switch the menu as expected.

In the example, I've opened the menu for filter 2, then clicked on filter 1, but the menu remains on filter 2. I would expect it to either change to filter 1, or to close.

Hmmm... when I click on Filter 2 module, the Picker Grid changes to Filter 2. Then clicking on Filter 1 changes the grid picker back to Filter 1. Works as expected here.

[exmatproton]

When the filter menu is open, clicking another filter to focus it doesn't switch the menu as expected.

In the example, I've opened the menu for filter 2, then clicked on filter 1, but the menu remains on filter 2. I would expect it to either change to filter 1, or to close.

Yes..you are not selecting the FILTER MATRIX but the module itself. The MATRIX only changes when you click the FILTER (in between the 4 arrows, on the left side of the module)

[joradn]

Hmmm... when I click on Filter 2 module, the Picker Grid changes to Filter 2. Then clicking on Filter 1 changes the grid picker back to Filter 1. Works as expected here.

To be clear, I'm not clicking on the filter visual that opens the menu, just a general area on the module.

Yes..you are not selecting the FILTER MATRIX but the module itself. The MATRIX only changes when you click the FILTER (in between the 4 arrows, on the left side of the module)

After checking again I realise that the filter menu does not always close when clicking on a different module, but it did for me the first time because I was clicking on the oscillator, which switches to the Osc 1 tab and closes the filter menu. However at this point, the filter menu can be freely opened, and you can click between the filter and oscillator without the filter menu closing, since the oscillator tab is already open. The behaviour is a bit inconsistent, but not the end of the world.

Edit: I'll record a video demonstrating things more clearly later on.

[pdxindy]

Hmmm... when I click on Filter 2 module, the Picker Grid changes to Filter 2. Then clicking on Filter 1 changes the grid picker back to Filter 1. Works as expected here.

To be clear, I'm not clicking on the filter visual that opens the menu, just a general area on the module.

Same, I select the Filter Module, and the Grid updates to the selected filter.