KVR Audio

eduardo_b · Post by **eduardo_b** » Wed Jan 23, 2008 5:36 am

BFunKu wrote:Ok where's the Download Link? How can you expect anyone to Buy your plug if you don't have a download link to try out the Demo?

His expectations may not match ours?

A3ntar · Post by **A3ntar** » Wed Jan 23, 2008 8:13 am

Hi Rene,

Nice to see you back as a developer on KvR. I wished I would see you back in a better situation like the release of the Guitar amp sim, and with everyone raving about it.

Unfortunately, I see that you are back instead with what sounds to me like an unfinished alpha product masqueraded as a retail package.

I am not for all that s l a m m ing both you and your product are getting on this thread, but I guess this is the way some KvR members like to operate, sad really...

Rene, what I suggest is that you ask the mods to lock this topic so it doesn't escalate to yet another fiasco, and go back to the DSP/architecture drawing board and see why all these anomalies are being produced. Get a good set of 10 or more beta testers (like you did for the ampsim) that are willing to lend you their ears and knowledge in the domain.

Sometimes you need that impartiality because Rene, you seem to me that your are a bit too much into it at the moment to fully and clearly comprehend the reasons others are complaining about the artifacts produced by Slammer.

When you are sure that the product is "usable" then you can go for a public beta and state it as such, and get yet more feedback from more people, and fine tweak the plug-in...and when you can fine tune no more and the general consensus is positive, you release it.

I don't see any good coming out from this thread, unless the next few releases is a complete 180 from the current one. The only thing this thread is succeeding in doing so far, is to inflict even more damage to the fragile reputation of SoundSpectral and yours, and to advertise that Inerthia compressor plugin.

shamann · Post by **shamann** » Wed Jan 23, 2008 12:40 pm

BFunKu wrote:Ok where's the Download Link?

[edit] not bumping the all-browser friendly link (demo down at moment).

Midiworks · Post by **Midiworks** » Wed Jan 23, 2008 2:16 pm

Sorry, demo removed until the next release.

btw, the clicks are gone WITHOUT losing the flexability,
the reason I left them in, in the 1st place.
(I had no problems dialing them out,
as you can hear with the audio demo)

shamann · Post by **shamann** » Wed Jan 23, 2008 3:43 pm

Midiworks wrote:I had no problems dialling them out, as you can hear with the audio demo

I think the clicks were harder to avoid when not adding gain after the compressor. I use compressors more for shaping than trying to make things really loud, so possibly I'm not your target market on this.

About the parameters, any way to get them to show in a host for MIDI assignment/automation?

Hink · Post by **Hink** » Wed Jan 23, 2008 4:31 pm

Midiworks wrote:Sorry, demo removed until the next release.

btw, the clicks are gone WITHOUT losing the flexability,
the reason I left them in, in the 1st place.
(I had no problems dialing them out,
as you can here with the audio demo)

so I'll delete the bump above to avoid confusion.

mangel1234 · Post by **mangel1234** » Wed Jan 23, 2008 6:09 pm

Midiworks wrote:Sorry, demo removed until the next release.

btw, the clicks are gone WITHOUT losing the flexability,
the reason I left them in, in the 1st place.
(I had no problems dialing them out,
as you can here with the audio demo)

So, the demo is gone, the clicks are gone, but you left them in to be flexible, and we can hear the demo that is gone because it was easy to dial it out?

Midiworks · Post by **Midiworks** » Wed Jan 23, 2008 8:26 pm

mangel1234 wrote:
Midiworks wrote:Sorry, demo removed until the next release.

btw, the clicks are gone WITHOUT losing the flexability,
the reason I left them in, in the 1st place.
(I had no problems dialing them out,
as you can here with the audio demo)
So, the demo is gone, the clicks are gone, but you left them in to be flexible, and we can hear the demo that is gone because it was easy to dial it out?

Midiworks wrote: http://hotsearch.us//downloads/vs_Slammer_vs.wav
5.45mb

http://hotsearch.us//downloads/vs_Slammer_vs.mp3
760kb

One of the 2 processed drums is S l a m m e r the other a highly regarded
expensive plug-in.

Those had never been removed, just buried in the posts here.

I think the clicks were harder to avoid when not adding gain after the compressor. I use compressors more for shaping than trying to make things really loud, so possibly I'm not your target market on this.

About the parameters, any way to get them to show in a host for MIDI assignment/automation?

S l a m m e r was never created to win loudness wars.
But as a creative tool, exactly to do this,
'shaping rather than trying to make things really loud'.

Sure I can re-activate automation.
(took actually sometime to de-activate it)
No problem, next version.

for full size, please click.

S-N-S · Post by **S-N-S** » Sat Mar 08, 2008 2:58 pm

when will there be a final version??

BertKoor · Post by **BertKoor** » Mon Apr 28, 2008 8:05 am

Is it still worth waiting?? [/bump]

Midiworks · Post by **Midiworks** » Mon Apr 28, 2008 8:37 am

BertKoor wrote:Is it still worth waiting??

Oh yes, I changed the inner structure and added a few things.
I keep the original version for myself and the new one
will fit a wider taste.

S-N-S · Post by **S-N-S** » Mon Apr 28, 2008 10:21 am

where can we get this,what will it cost,when is it available??

Midiworks · Post by **Midiworks** » Mon Apr 28, 2008 10:51 am

S-N-S wrote:where can we get this,what will it cost,when is it available??

Sorry, its not a priority at the moment.
I will make an anouncement here in time.
Thank you

S-N-S · Post by **S-N-S** » Mon Apr 28, 2008 1:27 pm

ahh its paypal only,nevermind

Slammer Vintage Valve Compressor