TAL Mod

[braj]

Would anyone chance a "this sounds a lot like this" classic synth guess?

[gentleclockdivider]

I really needs a modulation mixer.
The sound is just bloody great

[layzer]

A work in progress using TAL-MOD for SeqBass:
https://app.box.com/s/2oki5unmt8nzo1ofdfhapitosjaxfxf3

other stuff used:
synthguitar - Synth1
piano - 4Front Piano
Pads - KLC M1
drums - Linplug RMIV
DAW - EnergyXT2 v2.7

[Cinebient]

The +2 range for modulation really helps to get some sounds i couldn´t get before.
I´m now really interested. But still need some days to decide.
So far it´s nice.
I like it even a bit more than Bazille. (but i still prefer ACE also over Bazille).

[bite_me]

sequencer crashes bitwig and saving in custom folder is currently disabled.
big fun synth!

[layzer]

sequencer crashes bitwig and saving in custom folder is currently disabled.
big fun synth!

i can say i've had a crash while adjusting a velocity level on a step while a seq was playing under savihost. XP SP3 x32

edit: here is the error i get....
the sequencer wasn't even on.

[bite_me]

@layzer: Win7x64 and latest Bitwig here. Yes, velocity levels tend to crash.
Got crashes nearly everytime I touch them.

[fluffy_little_something]

Same bug in Mulab, serious crash

Is there a latch feature for the sequencer/arp?

The envelopes take some time to get used to, the first quarter or so is all very short, in the middle, however, the time increase is huge with tiny increments.

[gentleclockdivider]

Can someone confirm the following bug .
When using the low pas followed by either the notch /all pass filter in serial +reso.there is a conitinous zipper noise , play the low keys .

-Here's how to reproduce ..mute (volume 0) all osc's except osc1
-Set osc 1to full volume
-filter routing serial
-First filter any lowpass filter set to aroud 400 hz
-secon filter notch , full resonance .
-NOw sweep filter cut off 2 , to 40 hertz ..;zipper noise ...and it stays there ...
I guess it has something to do with the the oversampled notch filters behaving strange in the lower regions



Watch out ..high volume output
Here are the presets .( zip file containing 2 patches
https://app.box.com/s/6z5b43ljiuy94m0y0vffadgcl6q2abgv

[hesnotthemessiah]

Just had a very quick play with TAL Mod after purchasing it. In creating a patch I will often be adding cables and often deciding, halfway through connecting, that I do not actually want to complete a connection (as shown in the video):-

https://nevilletubb.tinytake.com/sf/MjU ... 83NTMzNjMx

As you can see, you then also lose a cable you connected previously.

I have also noticed that, by simply clicking on a source or destination that has a cable connected, you then lose cables:-

https://nevilletubb.tinytake.com/sf/MjU ... 83NTMzNzIz

By using a key command such as "CTRL" whilst clicking the actual cable to be removed, rather than simply clicking on a source or destination to remove it, would save a lot of accidental removal of cables.

Perhaps even a lock option where you can protect certain cables from removal?

I haven't read the manual yet.

Looking forward to having a play with this over the next few days.

[fluffy_little_something]

That is why I suggested right-clicking cables for deleting them. Because when you have more than one cable plugged into the same connector, they are removed from that connector in a specific order, which sucks.

[hesnotthemessiah]

That is why I suggested right-clicking cables for deleting them. Because when you have more than one cable plugged into the same connector, they are removed from that connector in a specific order, which sucks.

Yes, that would be a good alternative

[gentleclockdivider]

here the bug is more obvious ..hold low c2..and hear the noise creeping in
https://app.box.com/s/mngo8wu9r1wby5lf4ch6glspl2sjkixz

[chk071]

Would anyone chance a "this sounds a lot like this" classic synth guess?

Like all the TAL synths (well... except those which emulate other synths, obviously), probably the Roland Juno-60.

[fluffy_little_something]

Maybe I am wrong, but in my view it sounded (past tense, I have just removed the demo, will wait for the hopefully bug-free regular release) similar to the free JX-8P emulation, which might make sense as TAL seems to be specialized on Roland synths for whatever reason...

But I think it sounds different from Noisemaker, despite probably being its successor (the third modulation envelope looks very similar to the one in Noisemaker, the effects are also very similar, despite the rather different design).