u-he

electro · Post by **electro** » Sat Oct 05, 2013 6:53 pm

An I the only one that thinks it would be a good idea to have the input gain value permanently displayed on the large input knob?

megapiano · Post by **megapiano** » Mon Oct 07, 2013 11:59 am

Which Satin preset or other settings would you recommend for solo piano? Thanks.

By the way, I just tried the RP Mastering Tape preset on a sampled piano, and I could hear the nice subtle glue and the replacement of harsh digital artifacts with some subtle warmth...simply amazing! Well done, u-he!

nilhartman · Post by **nilhartman** » Mon Oct 07, 2013 4:05 pm

Even if the monitoring section is great and useful as is, I have a small suggestion : a small blue LED (similar to the Clip/Headroom ones) next to the meters, that would get brighter as the signal saturates.

sascha · Post by **sascha** » Mon Oct 07, 2013 6:25 pm

nilhartman wrote:Even if the monitoring section is great and useful as is, I have a small suggestion : a small blue LED (similar to the Clip/Headroom ones) next to the meters, that would get brighter as the signal saturates.

I'd consider that obsolete.
See, saturation can have 3 causes in Satin:

1) In one of the simulated circuits (eq, gainstages etc.). This would be shown by the 'headroom' LED.

2) Within the tape part. This is reflected by the VU meters when switched to 'input'. It depends a bit on the 'tape' model, but the reference point for 1% THD is around -15dBFS (look at the figures in the manual). So, if you set the VU reference to -15 approx., you have a good measure of the resulting signal. Keep in mind that the entire tape-saturation process is not frequency-linear, hence any visual indication isn't that much of value. Careful listening is mandatory.

3) The output circuit. It's got it's dedicated visualizer, plus the VU & peak meters when set to 'output'.

dorremifasol · Post by **dorremifasol** » Mon Oct 07, 2013 7:29 pm

Just wanted to say hello. Bought Satin yesterday ^^

sylvainmoreau · Post by **sylvainmoreau** » Mon Oct 07, 2013 11:10 pm

just bought it !
well uh i hope i did actually i had to go though that Mycomerce or is it Share it ? pff i'm lost this payment method is real pain in the ass i always forget what login it is have to ask for new password by mail blablabl...
please add some paypal directly on your website !

RexXx · Post by **RexXx** » Tue Oct 08, 2013 1:57 am

You don't need to login.
Just scroll down the "Your Cart" page and press "Check out with PayPal", done.

dorremifasol · Post by **dorremifasol** » Wed Oct 09, 2013 2:51 pm

When I load Satin into Wavelab 8 (64 bit) I get an error both in VST3 and VST2.4 formats.

VST3 says the plugin it can't handle the number of input channels (2!).
VST2.5 (Satin(x64)) tells it has no GUI resources.

Both work fine in Cubase 7.

bysbox1 · Post by **bysbox1** » Thu Oct 10, 2013 3:03 pm

dorremifasol wrote:When I load Satin into Wavelab 8 (64 bit) I get an error both in VST3 and VST2.4 formats.

VST3 says the plugin it can't handle the number of input channels (2!).
VST2.5 (Satin(x64)) tells it has no GUI resources.

Both work fine in Cubase 7.

I can confirm the first one. As far as VST2.4 (I think you meant VST 2.4), I had no problems. I was going to put in a trouble ticket with U-he.

For me right now it's no big deal since I can use VST2.4. But I would love to see this get fixed so I can use VST3 in Wavelab.

speed771 · Post by **speed771** » Sat Oct 12, 2013 3:09 pm

I have a session with only one audio track (stereo/44.1kHz/24 bit)

from one minute to another I can't open Satin in that session anymore. No matter where in mixer. (track/mixbus)

the moment I assign satin as insert Cubase freezes/becomes unresponsive.

no crashlog available

I can see black (inactive) insert for satin in mixer with red frame but nothing more. It's not properly loaded and Cubase waits.

this is very annoying. I tried to save new version but satin won't load anywhere in session.

loads fine in other projects. I'm using VST3 64-bit (only)

I'm on W8 x64, Cubase 7.0.6 64bit, latest version of Satin (re-installed today)

Urs · Post by **Urs** » Sat Oct 12, 2013 4:37 pm

speed771 wrote:I can see black (inactive) insert for satin in mixer with red frame but nothing more. It's not properly loaded and Cubase waits.

Does the project open if you temporarily put Satin.vst3 somewhere else, i.e. not a Vstplugins folder?

This one is definitely new to us. We have been informed by a Steinberg employee about a requirement of Cubase that goes beyond interpretive results of our exegesis of the VST3 specification. We'll make updates available asap, but I can't promise that this is the same problem that we're addressing.

Please let us kow what's happening with the removed plug-in.

Cheers,

- Urs

todd_r · Post by **todd_r** » Sun Oct 20, 2013 3:44 pm

Did I miss the intro period?

EvilDragon · Post by **EvilDragon** » Sun Oct 20, 2013 3:46 pm

4damind · Post by **4damind** » Sun Oct 20, 2013 3:54 pm

I have sometimes "pure virtual function call" errors and it seems only since using Satin as the vst3 version. Because it's the only new plug-in I used the last time, I would say it's Satin. I changed it to the vst2 version and since this time not such errors. (Cubase 7.0.6 64Bit)

todd_r · Post by **todd_r** » Sun Oct 20, 2013 6:47 pm

EvilDragon wrote:Yep.

Bugger

u-he

KVR Audio

Satin goes V1.1