KVR Audio

fisherKing · Post by **fisherKing** » Mon Aug 05, 2013 1:56 am

i use it a lot, for simpler things (than using the exs24). one of my favorite things is to sometimes write a part with one sample, then try something entirely different (with the same midi part). impossible with logic's sampler, and easy with nuance...

newsonicarts · Post by **newsonicarts** » Tue Aug 06, 2013 1:41 pm

analoguesamples909 wrote:
newsonicarts wrote:
but you are right about the non-realtime updating of the start/end points, makes sense and noted!
Cool I like this sampler but real time update is where things get really creative...and also a handle for the crossfade looping...would like to pick this up if it did that...its a great replacement for simpler and with a nice browser and more features...

Ok noted! But just to make sure we are on the same page, the loop is fully real-time modulatable by all modulation sources, so in terms of creativity I think it's already pretty comprehensive. But I defintely agree workflow could be improved if mouse editis were applied immediately, without needing to retrigger. It's on the FR list

SWAN808 · Post by **SWAN808** » Tue Aug 06, 2013 4:12 pm

newsonicarts wrote:
analoguesamples909 wrote:
newsonicarts wrote:
but you are right about the non-realtime updating of the start/end points, makes sense and noted!
Cool I like this sampler but real time update is where things get really creative...and also a handle for the crossfade looping...would like to pick this up if it did that...its a great replacement for simpler and with a nice browser and more features...
Ok noted! But just to make sure we are on the same page, the loop is fully real-time modulatable by all modulation sources, so in terms of creativity I think it's already pretty comprehensive. But I defintely agree workflow could be improved if mouse editis were applied immediately, without needing to retrigger. It's on the FR list

thanks - Ill look into using the LFO/Env. The thing about dragging is its a really quick creative way to find points...but I like how you have enabled to move both loop points together so its just the real time update...also the waveform xfade control a possibility?

Robmobius · Post by **Robmobius** » Tue Aug 06, 2013 6:41 pm

Interesting... That's the one thing I missed about Ableton was 'simpler'.

Might pick this up.

emerable · Post by **emerable** » Mon Aug 19, 2013 7:32 pm

newsonicarts wrote: and this now includes loop modulation, as well as a few other new modulation targets.

Could you explain how loop modulation is done?

newsonicarts · Post by **newsonicarts** » Tue Aug 20, 2013 5:09 pm

emerable wrote:
newsonicarts wrote: and this now includes loop modulation, as well as a few other new modulation targets.
Could you explain how loop modulation is done?

Loop is a target in the Modulation Matrix. So for example, if you want to close and open the loop with the mod wheel, add a slot to the matrix and set CC1 as the source and Loop as the destination. Hope that helps!

Echoes in the Attic · Post by **Echoes in the Attic** » Tue Aug 20, 2013 5:15 pm

Are you guys going to making mac VSTs?

zyguli · Post by **zyguli** » Wed Aug 21, 2013 12:38 pm

Are there any chances to see loopable multipoint envelopes?

newsonicarts · Post by **newsonicarts** » Wed Aug 21, 2013 7:20 pm

zyguli wrote:Are there any chances to see loopable multipoint envelopes?

Theoretically possible, but it's nothing planned at the moment...

newsonicarts · Post by **newsonicarts** » Wed Aug 21, 2013 7:23 pm

Echoes in the Attic wrote:Are you guys going to making mac VSTs?

Actually yes this is something planned, hopefully for later this year, although I have to make the usual disclaimer to say anything can change and I can't guarantee it will happen until it actually happens.

Robmobius · Post by **Robmobius** » Wed Aug 21, 2013 8:58 pm

I bought this, and I'm very pleased with it... I really like the filters. Good job!

kev2525 · Post by **kev2525** » Thu Aug 22, 2013 11:25 am

newsonicarts wrote:
hcv242 wrote:i like it but i find the fact that every zone has to use the same envelope settings or filter settings a no go. the same goes for reverse mode. if i have a program with multi samples and i select reverse, not only the selected zone gets reversed but all the other zones also. it doesnt make much sense. it seems it was designed to use only one sample / zone and not for multisamples / various zones.
Well, yes

Nuance is a single-instrument sampler. Its not a drum sampler or a multi-instrument sampler (yet...)

Any news on this feature development? Also, would think about adding a delay to the FX section at some point?

newsonicarts · Post by **newsonicarts** » Sat Aug 24, 2013 1:25 pm

kev2525 wrote:Any news on this feature development? Also, would think about adding a delay to the FX section at some point?

This is tricky to answer right now for reasons I cant fully disclose at the moment. Right now, I can say that yes, there will be a solution to this use-case (using Nuance for drums, multiple outs etc) in the near future, but probably not in the way you expect, and I can tell you now it wont be a free update. Same statement pretty much applies for adding delay FX too...

Sorry to have to be purposely vague at this point, but just wait a couple months and I think all will be clear and make sense. Trust me, its going to be cool

AgiKvr · Post by **AgiKvr** » Sun Dec 15, 2013 2:46 pm

any news/anticipations about nuance?

Keef Baker · Post by **Keef Baker** » Sun Dec 15, 2013 2:58 pm

Well granite got a nice new update recently so i expect there'll be something.

I love this thing even just for the unison feature.

Nuance, The Compact Sampler from New Sonic Arts