77 posts

RELATED
PRODUCTS

BCR2000 as a MCU extra presets & a mcu display app 2005-04-22T20:03:46+00:00 since doing this someone did one much better so go straight to page 5 of this thread for more info http://skirize.bounceme.net/mcu.zip Ok settings on this preset are mostly along the top! The top row of the main 24 controllers are the volume’s the four buttons in the bottom right are transport buttons. Play, bottom left. Record, hold down top left & press the play button below it. Stop & return to start are the same button, bottom right. The buttons above the volume controls are mutes & solos. The four banks of the very top row are all different! Bank 1, controller 7 is master volume. Controller 8 is the jog wheel Push buttons on the top row of bank 1, controller button 3, end 2 end. 4, punch. 5, click. 6, snap. 7, scroll. 8, loop Bank 2, controller 7 is master volume. Controller 8 is the jog wheel push buttons on bank 2, controller button 1, jumps the volumes, mutes solos & pans up 8 tracks. 2, jumps the volumes, mutes solos & pans down 8 tracks. 3, the volumes, mutes solos & pans up 1 track. 4, the volumes, mutes solos & pans down 1 track. 5, undo. 6, redo. 7, automation play. 8, automation record. Bank 3, all the controllers for this are pan’s for the track that it is on & all the push buttons arm the track for recording, Bank 4, doesn’t do any thing yet Neither dose the first 16 controllers from the bottom Also if you use the bcr input as a MCU it won’t let you also use it in the midi mapper! My work around for this was to use midi ox & midi yoke so I could patch the input to the midi yoke input & set the midi yoke to assign to stuff in the cc mapped in tracktion 2 If you do this set the properties for the midi yoke input to only receive data sent on channel 16 & set the controllers you map to out put from channel 16!!! The reason for this is that the MCU commands will also be sent to that input!! But none of them are on channel 16 On the other hand if you don’t want to use any other controllers for any thing then load the preset I have attached & set the bcr as the input for the MCU in the settings page I have also attached my preset for midi ox if you chose to install it if you do then you will need to make the midi yoke 1 input be the MCU input in the settings page!! But keep the bcr as the out put, if you do this you can just set the bcr input to map the cc commands for T2’s midi mapped (on channel 16 only don’t forget!) If you do use this preset in midi ox you will find that controllers 1 & 2 in bank 1 of the top row will let you zoom & scroll ;) Good luck let me know how you get on Subject ps sorry if this is hard to understand :oops: :oops: djsubject https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=49359

rainydays rainydays https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=66969: KVRist
Contact rainydays

Website; 474 posts since 1 May, 2005 from Sweden; Contact:
Contact rainydays

Website

Post by rainydays » Mon May 22, 2006 12:56 pm

0
Quote

Hi all,

Does anyone have the specs for the MCU MIDI chart? I have started to develop a controller software and it would be cool to be able to fully use it with Tracktion, and I guess MCU-support is the only answer to that.
Would it be worth the trouble to ask Mackie politely?

Barbarossa Barbarossa https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=39908: KVRian; 831 posts since 7 Sep, 2004

Post by Barbarossa » Mon May 22, 2006 7:30 pm

0
Quote

I think i have the MCU-MIDI-implementation chart at home. If you want it, let me know.

Post Reply

77 posts

Return to “Tracktion”

Tracktion Software

KVR Audio

BCR2000 as a MCU extra presets & a mcu display app