Analog Obsession released first reverb plugin "Room041"

[AnalogObsession]

First reverb plugin by Analog Obsession!

Not 1:1 modeling based on any device (it's room reverb plugin) but it has features like famous plate reverb!

Features

Preamp Section

DRIVE: +/-24dB input drive based on tube based reverb line input. Possible to get really dirty or clean reverb!

HPF: Pre-Filter 20 to 100Hz

Reverb Section

Stereo Sep.: Mono to Stereo stereo seperation

Pre-Delay: 0 to 250ms

Decay: 0.1 to 6 sec

Post Eq Section

Low: 20Hz to 2kHz with +/-24dB

High: 200Hz to 20kHz with +/-24dB

Master Section

DRY & WET: 0dB to inf

Available Formats

VST/VST3/AU | Mac 10.9 - 11.X

VST/VST3 | Windows 7 - 8 - 10

Coming Soon!

Patreon

[excuse me please]

Looks nice. Thanks for all the good work.

[crickey13]

Interesting to see the inclusion of the preamp section. Nice.

[sguyader]

The interface is cleaner than Arturia's emulation of the EMT 140, and that's good!

[pabloaldunate]

IR?

[AnalogObsession]

Hi all!

Thanks for your interest. It's coming really soon!

IR?

No IR. Fully algo.

Thanks!

[Halonmusic]

looks beautiful

[AnalogObsession]

Hi!

It's just released!

Check first post for link!

Enjoy!

[Agreed]

Looking forward to trying this out very shortly, thank you for this release

[sguyader]

Hi Tunca,
Two things:
1. At least on Reaper, turning Stereo sep. to 100 still gives mono signal
2. The drive is a bit too strong, in particular in the highs, I need to compensate with POST EQ (turn the highs down) and lower the drive, but then the overall reverb level can't be compensated within the plugin (there's no output compensation knob)

Even if your plugin is not a direct emulation of the EMT 140, below is comparison of the frequency responses of your plugin (top) with that of Arturia's Rev Plate-140 (bottom) :

100Hz sine tone, both plugins at 50% wet, drive at 0, decay at 5 sec, width at 0

AO-Room0410.png

Arturia-140.png

You can see how strong the harmonics of Room 041 are with drive at 0, in particular in the highs. Even with the drive at -24, the harmonics are still sronger.

[Obsolete462444]

Yes, I also found the drive / waveshaping a bit strong considering its a reverb (you often don't want drive on reverb signal). The reverb sound itself is great, reminds me of very well captured room impulses. I have my doubts this can be algorithmic? Definitely a keeper!

[hesnotthemessiah]

Hi Tunca,
Two things:
1. At least on Reaper, turning Stereo sep. to 100 still gives mono signal

The Room041 "STEREO SEP." control seems to be working correctly.

The Room041 "STEREO SEP." control just turns the wet audio to mono (mid and side audio the same).

I sent a mono signal to ROOM041 but with the audio send panned to the left. With "STEREO SEP." set to maximum, the wet audio was also panned to the left by the same amount. Then I slowly turned "STEREO SEP." to it's minimum setting and you could hear the wet audio turning into mono (side and mid audio the same).

[hesnotthemessiah]

Loving this!! Just experimenting putting a Room041 on two fx sends. Then send the same audio to each one. Pan the first send hard left to Room041 on fx send channel 1 and the other hard right to Room041 on fx send channel 2 . Have slightly different settings on each Room041 and create a nice stereo reverb effect. Need "STEREO SEP." at a reasonably high setting to hear the stereo effect but experiment with this setting. Sounds lovely with a TB-303.......just need to go to work now. Bugger!!

[Danilo Villanova]

Thanks! How is the cpu use?

[yorubamonk]

Thanks! How is the cpu use?

It's really low as far as reverbs go. I'm quite impressed!