KVR Audio

blackanom · Post by **blackanom** » Mon Jul 11, 2005 1:25 pm

I just picked up FL 5 and I was wondering, can you edit sample start and end points? Not loop points! Your help will be greatly apprieciated.

Igor 4000 · Post by **Igor 4000** » Mon Jul 11, 2005 1:37 pm

Amazingly enough you cannot currently do this. However their new sampler apparently will have this capability.

blackanom · Post by **blackanom** » Mon Jul 11, 2005 1:41 pm

What!?!?!?!?! That's one of the most basic functions of a sampler. Does anyone know when this new sampler will be out?

Totolitoto · Post by **Totolitoto** » Mon Jul 11, 2005 1:45 pm

Of course you can! Juste click on "INS" (between SMP and MISC on the sampler panel) and edit ADSR

[ xerocreep ] · Post by **[ xerocreep ]** » Mon Jul 11, 2005 2:14 pm

I have really wanted this feature also. It would be great to have it available in the piano roll events like velocity and filter cutoff, so you could adjust sample start position in the same space...

[edit: nevermind]

rbet · Post by **rbet** » Mon Jul 11, 2005 3:51 pm

Igor 4000 wrote:Amazingly enough you cannot currently do this. However their new sampler apparently will have this capability.

Yes you can, my son. Sending the sample to a new granulizer channel (and moving the start knob in the clockwise direction until required) should do it. You can even select the 'loop' button (just above that knob) if you need it; it's as simple as 1-2-4... err, 1-2-3 even! Now go play!

unless that is not what you are looking for

edit: yeah, totolito's method is cool too.

blackanom · Post by **blackanom** » Mon Jul 11, 2005 4:07 pm

AHHHH! I'll try that. Now, can you have multiple (samples/parts of a sample) on the same channel. Kind of like mapping slices but without the slicer (ie. key 1 is sample x and key 2 is copy of sample x with a different start point?)

verstaerker · Post by **verstaerker** » Mon Jul 11, 2005 4:09 pm

have u ever tried wave traveller?

blackanom · Post by **blackanom** » Mon Jul 11, 2005 4:31 pm

I looked at it and I know you can adjust the start point but (1) Can you just get it to play reg without the spline action and (2) Can you gat it to play multiple...(refer to my previous post)

verstaerker · Post by **verstaerker** » Mon Jul 11, 2005 4:38 pm

u can set multiple start points in wave traveler and map them to diffrent keys. This "spline action can be reset somewhere. Sorry i'm not using this to much, so i don't know exactly. I'm sure it's in the manual.

blackanom · Post by **blackanom** » Mon Jul 11, 2005 4:46 pm

Thanx Cuz

Igor 4000 · Post by **Igor 4000** » Tue Jul 12, 2005 6:26 pm

rbet wrote:
Igor 4000 wrote:Amazingly enough you cannot currently do this. However their new sampler apparently will have this capability.
Yes you can, my son. Sending the sample to a new granulizer channel (and moving the start knob in the clockwise direction until required) should do it. You can even select the 'loop' button (just above that knob) if you need it; it's as simple as 1-2-4... err, 1-2-3 even! Now go play!

Thank you, I stand corrected. Although the sampler (any sampler, for that matter) should have this function as well.

Edit start points in FL 5?