Tracktion Software

stash98 · Post by **stash98** » Thu Aug 25, 2005 6:04 pm

just wondering..how do you clear out all automation and start from scratch?

I deleted all the points from the curve, but one remained. I hide the automation (unhighliting the A), but I dont think that clears it out either. or doeas it?

when i go to the parameter, it is in green no matter what I do. a bit confusing.

ModuLR · Post by **ModuLR** » Thu Aug 25, 2005 6:24 pm

if there is only one point, just double click it...

stash98 · Post by **stash98** » Thu Aug 25, 2005 6:48 pm

thats the thing..i do that too.and it's still there.

ModuLR · Post by **ModuLR** » Thu Aug 25, 2005 6:52 pm

maybe I don't get it then... screenshot perhaps?

Beno · Post by **Beno** » Thu Aug 25, 2005 7:27 pm

select the curve, and there should be a delete all points from curve command in the properties panel.

IIRs · Post by **IIRs** » Thu Aug 25, 2005 9:45 pm

You do realise you can't get rid of the line completely? When all points are gone the line should display the current parameter value..

stash98 · Post by **stash98** » Fri Aug 26, 2005 12:06 am

yep..i tried every suggestion on here..Im still in this situation:

look at track 2..there is a dot there that wont go away.

because of this, I can't undo the automation.

IIRs · Post by **IIRs** » Fri Aug 26, 2005 12:25 am

Thats before the start of the edit! Does the parameter still show up highlighted, to show there is active automation? (drag the "A" to the plug to see the list).

A pretty sure way to remove automation is to delete the plug its tied to, and re-insert. (save a preset first though

)

stash98 · Post by **stash98** » Fri Aug 26, 2005 1:12 am

IIRs wrote:Thats before the start of the edit! Does the parameter still show up highlighted, to show there is active automation? (drag the "A" to the plug to see the list).

yep..its been highlighted..i cant get rid of it..so if deleting the plug is all i can do..thats cool..just wondering if there is a bug at work w/ guru or t2..its just a wierd scenario because mapping my controller to guru caused this whole thing.

IIRs · Post by **IIRs** » Fri Aug 26, 2005 1:22 am

Well, maybe you should send that edit to Beno, or Mackie support: I don't think you should be able to get automation points before the start of the edit.

stash98 · Post by **stash98** » Fri Aug 26, 2005 2:34 am

yeah, i can send him the edit if he wants it..it may be an issue with Guru. I hope the guru-tracktion glitches get ironed out, because they pack an extremely powerful 1-2 punch.

Beno · Post by **Beno** » Fri Aug 26, 2005 7:23 am

yeah looks like a little buglet that somehow got the automation before time 0. Can you save a copy of the edit and delete all other tracks and all filters except Guru. Then save an archive of the edit and send it to techmail@mackie.com "attention Beno"

stash98 · Post by **stash98** » Fri Aug 26, 2005 11:28 pm

im going to have to recreate it..before i saw your post, i noticed that my automation record button was on...what's wierd is it wasn't on in the screen shot..so i turned it off and then double clickign worked..but im going to automate this sub again (or try to) so we will see what happens.

Tracktion Software

KVR Audio

automation..