Acoustic Drum Library V2 - 30 MB download - 150 MB kit, free

[Spe3D]

This is a quick demo mp3 from the RM-4 version

http://spe3d.com/audio/Spe3d_ACUDRUMSV2_RM4_DEMO.mp3

http://spe3d.com/audio/Spe3d_ACUDRUMSV2_RM4_DEMO2.mp3

This kit has the cymbals spread out better (I know some got confused by the Bells of the cymbals getting hit), added a china HH 14” and a HH 12” splash (just one hit from them ) and there are 10” – 12” – 14” – 15” and 16” Toms with Evans and Remo heads plus a Steel Snare 14” hit with either wood or nylon tipped drumsticks – the Kick has been re-done plus I added a bit of distortion and a SubSonic thump, I ran out of pads but there is room on the RM 4 to add extra sounds but assign them to different keys, so from the keyboard or piano roll you will be able to audition them.

The sounds were recorded at 24-96 and then converted to 16 bit 44.1

Download the WAVES - RM4 - DR008 from the Auditorium here

http://audioshots.com/auditorium/viewtopic.php?t=3044

or from the AudioShots site here

http://audioshots.com/index.php?option= ... iew&id=165

Archives are 30 MB in size, typically expanding to 150 MB on the disk once extracted.

Best regards,

Peter

[Kriminal]

Look forward to grabbing those Peter, cheers.

[Spe3D]

Cool Krim

RM4 version is now up grab it from here

http://www.kvraudio.com/forum/viewtopic ... 86#1500486

Best regards,

Peter

[Spe3D]

Ok waves and DR-008 mapping at the Auditorium on this link (its in the sample section)

http://audioshots.com/auditorium/viewtopic.php?t=3044

Best regards,

Peter

[pw]

thanks again for these kits!

[maximilians1]

awesome Peter, can't wait to try these, thanks!

[pw]

Hopefully I will get some maps done for DK+ in the next week or two.

[Spe3D]

Thanks guys

Best regards,

Peter

[Spe3D]

Someone asked for the layer info.

So by pads its

Kick 1 – two layers fast kick 20”

Kick 2 D – three layers, low kicks with a tad of variation and main distortion on the mid velocity 20”

SUBSONIC – one very low rumble kick for those with subs

SSNARE 1 – Two layers for a Single hit Steel Snare 14”

SSARE 2 – Two layers each with a double hit on the Steel Snare 14”

BSNARE – just a couple of layers of the high toned 10” snare so you can see where it is in the kit from version 1

LFTOM 16 – Five layered 16” Floor Tom

HAT CL – 3 Layers of a peddle hat, 2 lower velocity layers from the closed hat being hit with a wood tipped drumstick, the higher velocity layer going from open to close with the peddle

MFTOM 15 – Four layers from a resonate but low toned 15” Tom

HAT OC – Two layers lower velocity open to close peddle, higher velocity a hit n rattle fx to close peddle

RLTOM 14 – Three layers, Low resonate 14” Tom

HAT OP – Four layers of an heavy open hat (carried over from version one)

RETOM 12 – Three layers from a 12” Tom

RETOM 10 – Four layers from a 10” Tom

CRASH 16 – 5 layers from a heavy 16” crash

CRASH BELL 16 – 3 Layers from the bell only getting hit on a 16” crash cymbal

RIDE 20 – Three layers from a heavy 20” Ride

HCHINA14 – 1 Layer hit from a Hand Hammered 14” china cymbal

RIDEBELL - 1 Layer from a the Bell part of the 20” ride

HHSPLASH 12 – 1 Layer from a Hand Hammered 12” Splash

Hit the things harder for the broad open long toned or fx’ed sounds – like the cymbal crashes.

Best regards,

Peter

[Spe3D]

bump!

[Spe3D]

last bump!

[silicon/silicium]

bump, thanks for this kit!!

[Spe3D]

bump, thanks for this kit!!

Thank you silicon/silicium

and thank you for the bump! too

Best regards,

Peter

[johne981]

Thanks for these kits,I haven't tried this one yet but v1. was excellent. I've used your more unusual samples like the balloon, noise and rain samples in a few things, they sound great through some of the camelspace presets.

[Spe3D]

Thank you johne981 ,

Hey that’s great news about the noise samples , I feel compelled to make some more of those now – its given me an idea, will upload that tomorrow

Best regards,

Peter