KVR Audio

DuX · Post by **DuX** » Wed Aug 02, 2006 11:43 pm

Changes are good: 1st=

, 2nd=2x

, 3rd=3x

.

All seems to be OK, doesn't feel so "beta".

Cheers!

Christian Budde · Post by **Christian Budde** » Thu Aug 03, 2006 1:39 am

DuX wrote:All seems to be OK, doesn't feel so "beta".

The only reason for being beta is because we simply haven't performed our quality tests/rules. One rule for example is: always sleep at a night before the final release. So good night,

Christian

Kermit Jagger · Post by **Kermit Jagger** » Thu Aug 03, 2006 1:53 am

I wanted to try Electri-Q but there is a problem. It uses the ID AMEQ which has already been registered by u-He for Filterscap, and you cannot install two plugs with the same ID on Receptor or in Plogue Bidule.

Could you change your ID to something that has not been registered ?

asseca · Post by **asseca** » Thu Aug 03, 2006 7:52 am

The new stuff seems to work fine ...

However I have found some "strange behaviour" in energyXT:
When I switch for example between "Linear Phase" and "Analog", Electri-Q loses it's audio input connector ...

Also, I consistently have a much higher latency when trying to use "Linear Phase" or "Maximum Phase", (180ms when compared against VoxengoAudioDelay)

Both problems also occur in previous versions of Electri-Q ...

Christian Budde · Post by **Christian Budde** » Thu Aug 03, 2006 10:33 am

asseca wrote:However I have found some "strange behaviour" in energyXT:
When I switch for example between "Linear Phase" and "Analog", Electri-Q loses it's audio input connector ...

The problem is known and I thought I had fixed it already

Anyway I've already contacted Jorgen, but never got an answer on this one. I have to write host dependend code in this case, but I think i can merge it into v.1.5.5. At least I know, what the problem is here.

asseca wrote:Also, I consistently have a much higher latency when trying to use "Linear Phase" or "Maximum Phase", (180ms when compared against VoxengoAudioDelay)

I fear I can't do anything about it (so far I know). I would have to tell the host that the latency has changed. For most hosts this works by using the 'IOchange' command, but in case of eXT it always looses connections so I have to drop it for that host. I don't have a clue, how to make it work in eXT, but I'll have an extra look.

Christian

asseca · Post by **asseca** » Thu Aug 03, 2006 10:36 am

It might be wise to write in the Manual that the "Linear Phase" and "Maximum Phase" modes are not real-time, and have a latency of 180ms ...

Christian Budde · Post by **Christian Budde** » Thu Aug 03, 2006 10:43 am

asseca wrote:It might be wise to write in the Manual that the "Linear Phase" and "Maximum Phase" modes are not real-time, and have a latency of 180ms ...

Yes it is. For me it was maybe to clear because both can't be realized without any latency, but we will add that...

_dada_ · Post by **_dada_** » Thu Aug 03, 2006 5:40 pm

Christian Budde wrote:I fear I can't do anything about it (so far I know).

There would be a solution.
It would cause some extra work, though.

Rim Buntinas has released an additional 'fixed latency' version of Drumagog,
to circumvent these problems.
It reports it's max latency to the host and internally adds a 'pseudo' latency for modes, that do not have any ...

As such a version of Electri-Q would not be usable for realtime work,
it would also have to be an additional version ...

robenestobenz · Post by **robenestobenz** » Thu Aug 03, 2006 6:59 pm

Christian Budde wrote:I fear I can't do anything about it (so far I know). I would have to tell the host that the latency has changed. For most hosts this works by using the 'IOchange' command, but in case of eXT it always looses connections so I have to drop it for that host. I don't have a clue, how to make it work in eXT, but I'll have an extra look.

Christian

Do the wire connections literally break? Very happy with Electri-Q by the way, great plugin. Looking forward to when I'm strongly familiar with all the different band types.

asseca · Post by **asseca** » Fri Aug 04, 2006 9:50 am

robenestobenz wrote:
Christian Budde wrote:I fear I can't do anything about it (so far I know). I would have to tell the host that the latency has changed. For most hosts this works by using the 'IOchange' command, but in case of eXT it always looses connections so I have to drop it for that host. I don't have a clue, how to make it work in eXT, but I'll have an extra look.

Christian
Do the wire connections literally break? Very happy with Electri-Q by the way, great plugin. Looking forward to when I'm strongly familiar with all the different band types.

Yes ... ONLY when switching between Real-Time modes (Analog,Digital,Screaming,British) and non-Real-Time modes (Linear,Maximum)

robenestobenz · Post by **robenestobenz** » Fri Aug 04, 2006 6:46 pm

Ah, I wonder if this is an XT problem then? It happens with other plugins as well.

asseca · Post by **asseca** » Sat Aug 05, 2006 5:34 am

robenestobenz wrote:Ah, I wonder if this is an XT problem then? It happens with other plugins as well.

I suspect it is ...

Volcomstone · Post by **Volcomstone** » Wed Aug 09, 2006 6:19 pm

So Christian, how's work proceeding on a new version?

Christian Budde · Post by **Christian Budde** » Wed Aug 09, 2006 8:37 pm

Volcomstone wrote:So Christian, how's work proceeding on a new version?

We found some bugs, so we skiped a release for within this week. There's still one evil in. Perhaps tomorrow, perhaps later,

Christian

Christian Budde · Post by **Christian Budde** » Fri Aug 11, 2006 12:06 am

Version 1.5.5 is confirmed and uploaded do our server. Unfortunatley our webmaster is on holidays, so we can't change it on our website. Feel free to download the version by using the link above or wait for version 1.5.6 which will feature the 'overview' window a little bit.
I forgot that feature completely, but it will have its renaissance...

Kind regards,

Christian

Electri-Q v1.5.4 released