Improvements!

Official support for: u-he.com
Post Reply New Topic
RELATED
PRODUCTS

Post

This might be a bit crazy. But don't spit on me. It would be nice to have a valeu indication in MSEG. So if I lift some points up it shows me the value. It would make life easier when messing with pitch shifting. LFO when set to user mode could have this too. Also (I'm not sure if this stuff patented, tell me if it is) quite nice feature is in Absynth with that lfo on an envelope.
Top

Post

What's crazy with that? - I thought I had that value readout already in... but d'oh...

Will see how it goes when back from holidays...

Reg. LFOs vs. Envelopes... I thought Loops in envs do the trick, or ModMixers...

;) Urs
Top

Post

Oh sorry I always forget about MMix.
Top

Post

chaoticz wrote:Also (I'm not sure if this stuff patented, tell me if it is) quite nice feature is in Absynth with that lfo on an envelope.
I didn't care for those LFOs on each and every every section of the Absynth envelopes, myself. I think thought they were way over the top, and not very useful. What I DID like was that "controller driven" mode - haven't seen it anywhere else (might be patented).
Top

Post

In the mod mixer module, an amount/depth parameter for each of the sources would be very useful...

Or is there another way of doing that that I don't know about?

Cheers,
Bagginz
Top

Post

...oops double post...
Top

Post

mis-posted........
Top

Post

bagginz wrote:In the mod mixer module, an amount/depth parameter for each of the sources would be very useful...Or is there another way of doing that that I don't know about? Cheers,Bagginz
In "Fade 1/2 by 3xC" mode, leave slot 3 empty. "Constant" balances between 1 and 2. Basta!
Top

Post

Can we have a multi and mass select in MSEG? So that it's possible to delete or to move a section of points.
Top

Post

chaoticz wrote:Can we have a multi and mass select in MSEG? So that it's possible to delete or to move a section of points.
Possibly...

I had some reasons to do multiple select in waveforms but not in MSEGs. Fortunately I have forgotten what these reasons were. So there's a chance that multiple select jumps into focus at one point... :oops:

Later,

;) Urs
Top

Post

Also a reset for MSEG would be nice :)
Top

Post

Howard wrote: In "Fade 1/2 by 3xC" mode, leave slot 3 empty. "Constant" balances between 1 and 2. Basta!
Cheers Howard :)

But as I thought, no way to utilize all three. Not a big deal, but would be useful...

Regards,
bagginz
Top

Post

bagginz wrote:But as I thought, no way to utilize all three.
Yep. Unfortunately, you can't feed one mod-mixer into another. However, you can always use multiple routings (in the target module itself or in the matrix) for such special cases. There's usually a way to do ANYTHING in Z2, although this sometimes needs a bit of thought!

Can anyone emulate Virus-style serial filter routing? After all these years, I still can't get my head around it enough to set up the same in Z2.
Top

Post

Howard,
not as elegant a solution as the Virus' single knob, but here's a stab at it:

http://media.twango.com/m1/original/008 ... e75c0c.JPG

The mix control on Channel mix 1 (bottom left)will give you a balance between filter 1 (at 0%) and both filters fully in serial at 100%

The mix control on Channel mix 2 will give you a balance between filter 1 (at 0%) and Filter 2 at 100% , with both in parallel at 50%

Not totally sure what happens if you mix the two...

Regards,
bagginz :D
Top

Post

Is it possible to make global pitch as modulation target?
Top
Post Reply

Return to “u-he”