MeldaProduction

soulxcity · Post by **soulxcity** » Sun Dec 06, 2009 1:40 am

a dj mixing program that takes the basics of twist and burn

http://www.acoustica.com/dj-twist-burn/

and includes twin decks, cue-ing etc.

cransky · Post by **cransky** » Wed Dec 09, 2009 2:38 am

Set the standard for a new electronic drum synth, with samples from all the great drum machines around the world.

This is the only path Melda could conceivably take, given the applications designed other than rhythm composition are free.

MeldaProduction · Post by **MeldaProduction** » Fri Dec 11, 2009 12:09 pm

AL321 wrote:Another thing i'd like to see, is the ability to morph between the A,B,C etc, so it works as a preset morpher.
Maybe two boxes '1' and '2'. And we can assign any of the A,B,C etc into those two boxes, and use one envelope lane to go completely over the top on sound mangling.

Or even simpler:
A single A/B morph envelope, so we can morph between the first two sets, and use C,D,E etc for backup/comparing.

Oukey doukey, I already thought about it, but there are some troubles (some parameters just cannot be morphed), but I guess it can work out

.

MeldaProduction · Post by **MeldaProduction** » Fri Dec 11, 2009 12:12 pm

cransky wrote:Set the standard for a new electronic drum synth, with samples from all the great drum machines around the world.

This is the only path Melda could conceivably take, given the applications designed other than rhythm composition are free.

Well, here comes a question - MSynthesizer4NN is a generalization of all drum synths I'm aware of. So why not to use it? Because it is easier to use special synth with a few knobs designed for particular drum type?

Igro · Post by **Igro** » Fri Dec 11, 2009 12:13 pm

Good sounding Tube/Tape (two in one) saturator.

svrc · Post by **svrc** » Fri Dec 11, 2009 12:42 pm

Msampler could be ok

AL321 · Post by **AL321** » Sat Dec 12, 2009 5:09 am

MeldaProduction wrote: Oukey doukey, I already thought about it, but there are some troubles (some parameters just cannot be morphed), but I guess it can work out .

Seriously, that would be amazing. I remember spending hours looking for something that could do preset morphing, and all i found was one single Mac plugin. I recently discovered the Morfiki plugins but sadly they crashed Sonar whenever i tried to save a song with them in (and corrupted my song file!!).
If only certain parameters can be morphed, maybe have a little button somewhere that opens a little box, and lets you tick the morphable parameters you want to include in the morph? Just a thought.
Or maybe grey-out the parameters, when the plugin is in 'Morph Mode', so people know those parameters can't be morphed.
Anyway, hope you figure something out.

ozmoz2008 · Post by **ozmoz2008** » Sat Dec 12, 2009 5:43 am

Pat2070 wrote:...Just for a bit of fun, if Melda were to release a new piece of software, what would you like to see?

A low cpu demanding denoiser would be always welcome here.

MeldaProduction · Post by **MeldaProduction** » Sat Dec 12, 2009 12:14 pm

AL321 wrote:
MeldaProduction wrote: Oukey doukey, I already thought about it, but there are some troubles (some parameters just cannot be morphed), but I guess it can work out .
Seriously, that would be amazing. I remember spending hours looking for something that could do preset morphing, and all i found was one single Mac plugin. I recently discovered the Morfiki plugins but sadly they crashed Sonar whenever i tried to save a song with them in (and corrupted my song file!!).
If only certain parameters can be morphed, maybe have a little button somewhere that opens a little box, and lets you tick the morphable parameters you want to include in the morph? Just a thought.
Or maybe grey-out the parameters, when the plugin is in 'Morph Mode', so people know those parameters can't be morphed.
Anyway, hope you figure something out.

Oukey doukey, will check it out

MeldaProduction · Post by **MeldaProduction** » Sat Dec 12, 2009 12:15 pm

ozmoz2008 wrote:
Pat2070 wrote:...Just for a bit of fun, if Melda were to release a new piece of software, what would you like to see?
A low cpu demanding denoiser would be always welcome here.

I already thought about that one - technically I think it is the last thing missing in MTotalBundle, so it would be good to have it there.

ozmoz2008 · Post by **ozmoz2008** » Sat Dec 12, 2009 4:23 pm

MeldaProduction wrote:
ozmoz2008 wrote:
Pat2070 wrote:...Just for a bit of fun, if Melda were to release a new piece of software, what would you like to see?
A low cpu demanding denoiser would be always welcome here.
I already thought about that one - technically I think it is the last thing missing in MTotalBundle, so it would be good to have it there.

Great! Make sure that there is noise sampling and some features that can adjust the different levels.

The best one I fund so far is Izotope RX(a good reference for you maybe), but it is still very cpu demanding.

Thanx for your hard work.

MeldaProduction

KVR Audio

What should Meldaproduction Make Next?