How do I tell MuLab to listen to a USB-Host input? I tried Edit >Midi Setup and nothing. I would like to use this keyboard as a controller.
MuLabs Version: 3.2.2
OS Windows7/32bit
Synth- Yamaha YPG 535
How to connect using USB Host
-
- KVRAF
- 7412 posts since 8 Feb, 2003 from London, UK
MU.LAB will display any MIDI Input devices available at the time you started MU.LAB. If you connect a device after starting MU.LAB, it won't be available.
-
- KVRist
- Topic Starter
- 96 posts since 20 Jul, 2010 from Los Angeles
HI KVRAF correction - pljones, (edited)
I stated that I am using a USB/MIDI cable connection. I can not get MU.LAB to see my Yamaha. Is there any documentation on how to successfully connect using a USB/Host connection?
Caps
I stated that I am using a USB/MIDI cable connection. I can not get MU.LAB to see my Yamaha. Is there any documentation on how to successfully connect using a USB/Host connection?
Caps
Last edited by Caps on Fri Jul 23, 2010 5:48 pm, edited 1 time in total.
-
- KVRAF
- 7412 posts since 8 Feb, 2003 from London, UK
Who are you addressing?Caps wrote:HI KVRAF,
This should be supported by the OS as a MIDI Port. If not, then no application that accesses MIDI ports will see it.Caps wrote:I stated that I am using a USB/MIDI cable connection.
Did you connect it before starting MU.LAB?Caps wrote:I can not get MU.LAB to see my Yamaha.
Have you read your USB/MIDI cable's manual?Caps wrote:Is there any documentation on how to successfully connect using a USB/Host connection?
-
- KVRian
- 1233 posts since 29 Dec, 2008 from Lithuania
I am using a M-Audio Radium, which is a USB midi controller and I never had any problems in Mu.Lab.
I guess it's short for KVR Audio Friends ???pljones wrote:Who are you addressing?Caps wrote:HI KVRAF,
-
- KVRist
- Topic Starter
- 96 posts since 20 Jul, 2010 from Los Angeles
My mistake,
I corrected that entry from "KVRAF" to "pljones." There is no USB/MIDI cable's manual. Will just purchase a MIDI interface - may be just easier than trying to figure this out
.
Caps
I corrected that entry from "KVRAF" to "pljones." There is no USB/MIDI cable's manual. Will just purchase a MIDI interface - may be just easier than trying to figure this out
.The drivers are all installed and when I turn off the Yamaha, the USB disconnect, audio alert sounds out.This should be supported by the OS as a MIDI Port. If not, then no application that accesses MIDI ports will see it.
Yes, I've tried all kinds of combination to initialize this. I've also followed the PDF manual which instructs on how to send MIDI data out.Did you connect it before starting MU.LAB?
Caps
Last edited by Caps on Fri Jul 23, 2010 8:36 pm, edited 1 time in total.
-
- KVRAF
- 7412 posts since 8 Feb, 2003 from London, UK
OK... Does the Yamaha come with its own drivers or use the Windows ones? If it comes with its own drivers and you're running a 64bit OS, do the drivers support 32bit apps?
Get a program like MIDI-OX and see what MIDI Ports it reports. Is the Yamaha shown?
Get a program like MIDI-OX and see what MIDI Ports it reports. Is the Yamaha shown?
-
- KVRist
- Topic Starter
- 96 posts since 20 Jul, 2010 from Los Angeles
Hi pljones,
Yes I download and installed the Window7/32 bit for my OS from the Yamaha download site. I can see the hardware status reflect the Yamaha within the System Device.
Will search for MIDI-OX. I was thinking that if the MIDI connection is via USB cable than MU.LAB would need to know.
Thank you again,
Caps
Yes I download and installed the Window7/32 bit for my OS from the Yamaha download site. I can see the hardware status reflect the Yamaha within the System Device.
Will search for MIDI-OX. I was thinking that if the MIDI connection is via USB cable than MU.LAB would need to know.
Thank you again,
Caps
-
- KVRist
- Topic Starter
- 96 posts since 20 Jul, 2010 from Los Angeles
Connection problem solved,
All working nicely now. I did nothing. I shutdowm the computer. Upon a restart, it now interacts with MU.Lab. Thank you Pljones for your sincere willingness to help.
Caps
All working nicely now. I did nothing. I shutdowm the computer. Upon a restart, it now interacts with MU.Lab. Thank you Pljones for your sincere willingness to help.
Caps