LinPlug

Teksonik · Post by **Teksonik** » Fri Oct 29, 2010 10:54 am

Peter from LinPlug wrote:
Teksonik wrote: Out of curiosity why not include it in the Demo?
Because it seems to disturb some people (no kidding), and because most people don't do presets from scratch. Think of the demo as coming with 70 different init patches instead

Oh ok if you say so. I wonder why would it disturb some people? I get the impression that a lot of KVR members like to roll their own presets from scratch so a blank preset is the perfect place to start. Maybe it's just me..............

Teksonik · Post by **Teksonik** » Fri Oct 29, 2010 11:19 am

Hmmmm quick question. The Morph wheel effects LFO speed? I've setup a patch where part B has an LFO to Filter Cutoff and as I raise the Morph wheel the speed of the LFO increases............my fault or is this by design?

Peter from LinPlug · Post by **Peter from LinPlug** » Fri Oct 29, 2010 11:44 am

No fault, no design, if A and B have different LFO speed, than speed changes during morphing.

blueghost · Post by **blueghost** » Fri Oct 29, 2010 12:13 pm

Important update - it can be automated in Frooty through assignng it a controller value no higher than 50

Badge · Post by **Badge** » Fri Oct 29, 2010 12:30 pm

Teksonik wrote: ...I get the impression that a lot of KVR members like to roll their own presets from scratch so a blank preset is the perfect place to start. Maybe it's just me..............

Nope, it's not just you

Gribs · Post by **Gribs** » Fri Oct 29, 2010 1:15 pm

Badge wrote:
Teksonik wrote: ...I get the impression that a lot of KVR members like to roll their own presets from scratch so a blank preset is the perfect place to start. Maybe it's just me..............
Nope, it's not just you

LOL. It is not exactly a stretch to make your own Init preset. The cool thing is once you set it up for A or B it is a breeze to copy it over to the opposite patch.

My Init preset might be different from yours too

Teksonik · Post by **Teksonik** » Fri Oct 29, 2010 11:01 pm

Gribs wrote:
Badge wrote:
Teksonik wrote: ...I get the impression that a lot of KVR members like to roll their own presets from scratch so a blank preset is the perfect place to start. Maybe it's just me..............
Nope, it's not just you
LOL. It is not exactly a stretch to make your own Init preset.

It's not exactly a stretch to make any patch.........but having a blank patch already included saves me time when trying to demo a new synth.........

Teksonik · Post by **Teksonik** » Fri Oct 29, 2010 11:09 pm

Peter from LinPlug wrote:No fault, no design, if A and B have different LFO speed, than speed changes during morphing.

Ahhh ok got it....I didn't have Part A's LFO's assigned to anything so I didn't take their speed into consideration. Indeed matching the speed works perfectly. So I assume Part A LFO 1 is linked to Part B LFO 1 and LFO 2 is linked to LFO 2..............

Xenox.AFL · Post by **Xenox.AFL** » Fri Oct 29, 2010 11:39 pm

Peter from LinPlug wrote:No fault, no design, if A and B have different LFO speed, than speed changes during morphing.

That's also the reason why peter called this synth "morphoX"

Peter from LinPlug · Post by **Peter from LinPlug** » Sat Oct 30, 2010 7:37 am

So you already discovered an important trick:)

Teksonik · Post by **Teksonik** » Sat Oct 30, 2010 10:24 am

Xenox.AFL wrote:
Peter from LinPlug wrote:No fault, no design, if A and B have different LFO speed, than speed changes during morphing.
That's also the reason why peter called this synth "morphoX"

Really? It's just not too obvious that a parameter that isn't in use would have an effect on a parameter that is in use.........So do the Delays Morph that way as well?

Teksonik · Post by **Teksonik** » Sat Oct 30, 2010 10:28 am

Peter from LinPlug wrote:So you already discovered an important trick:)

Yes if one wishes to increase or decrease LFO speed with the Morph wheel this is a perfect trick. If one wishes for the LFO speed to remain constant just match the speed of each part's LFO.

Peter from LinPlug · Post by **Peter from LinPlug** » Sat Oct 30, 2010 11:28 am

Teksonik wrote: Really? It's just not too obvious that a parameter that isn't in use would have an effect on a parameter that is in use.........So do the Delays Morph that way as well?

Morphing means thats everything changes from A to B in a certain way. There is no exception, like "being in use" or not. Actually this would make it quite hard to grasp. Its simply changing from A to B allways, no matter how you route certain things. The delay in example does not morph time but blend signals as morphing time would introduce (in most cases) unwanted pitch effects, however when it comes to feedback, the delay gradually changes feedback between the two settings A and B.

Anyway, trying is better than talking, I admit that certain things are not obvious, but thats part of the fun to being able to dive deeper and deeper into it.

djsubject · Post by **djsubject** » Sat Oct 30, 2010 11:41 am

may i ask a Question thats somewhat off topic

was the naughty word MotherPhucker in any way a influence in this products name?

i cant help but read Mofo-X when ever i read the product name

PS beast of luck with every thing!

Subz

Peter from LinPlug · Post by **Peter from LinPlug** » Sat Oct 30, 2010 1:05 pm

Thats just your brain

Pete

LinPlug

KVR Audio

MorphoX Released