u-he

Urs · Post by **Urs** » Thu Dec 15, 2011 7:36 pm

Ch00rD wrote:(Diva rev 472)

- Select Dual VCO 2 oscillators module;
- Set octave knob for oscillator 2 fully clockwise (2');
- Set detune knob (oscillator 2) fully clockwise (value display = 30.00);
- Double click on detune knob to reset its position.

The value display = 36.00, but detune is audibly still at 30.00, and the osc2 octave knob disappears.
It's probably trying to display itself in a 1' position for which it has no image.

Eeeek.

Urs · Post by **Urs** » Thu Dec 15, 2011 7:37 pm

hakey wrote:Found a possible bug with the modifications page.

The patches in the link below are identical, save for in "patch 2" the output from Multiply is routed through the Adder module. Only one signal is running into the Adder, so the signal should pass through it unaffected. However, that's not what happens. Patches here.

Edit: voice stack seems to be involved (the problem disappears when voice stack is set to 1)

Gonna check this out too... tomorrow

hakey · Post by **hakey** » Thu Dec 15, 2011 7:45 pm

Urs wrote:
hakey wrote:Found a possible bug with the modifications page.

The patches in the link below are identical, save for in "patch 2" the output from Multiply is routed through the Adder module. Only one signal is running into the Adder, so the signal should pass through it unaffected. However, that's not what happens. Patches here.

Edit: voice stack seems to be involved (the problem disappears when voice stack is set to 1)
Gonna check this out too... tomorrow

I guess it wasn't you who dl'd the (now deleted) patches?

I'll re-up them just in case.

Patches

jumpercable · Post by **jumpercable** » Thu Dec 15, 2011 8:43 pm

In ableton Live 8.2.7
Osx 10.6.8

Load the Diva AU
Delete
Load the Diva Vst
Delete
Load the Diva AU - the gui wont reappear for the AU. Not until you restart ableton.

hakey · Post by **hakey** » Thu Dec 15, 2011 10:24 pm

Don't know if this is a bug, but selecting 'analog1' for the triangle shape in the Dual VCO seems to change the sound of all waveshapes - the saw is slightly rounded, the sine squarish, the triangle closer to a sine, and all are slightly attenuated.

Howard · Post by **Howard** » Thu Dec 15, 2011 10:26 pm

Urs wrote:
Ch00rD wrote:It's probably trying to display itself in a 1' position for which it has no image.
Eeeek.

Same in Triple and Dual2 (BTW I wish all those modules already had a single, simple name each!)

Urs · Post by **Urs** » Thu Dec 15, 2011 10:26 pm

hakey wrote:
Urs wrote:
hakey wrote:Found a possible bug with the modifications page.

The patches in the link below are identical, save for in "patch 2" the output from Multiply is routed through the Adder module. Only one signal is running into the Adder, so the signal should pass through it unaffected. However, that's not what happens. Patches here.

Edit: voice stack seems to be involved (the problem disappears when voice stack is set to 1)
Gonna check this out too... tomorrow
I guess it wasn't you who dl'd the (now deleted) patches?

I'll re-up them just in case.

Patches

I did d/l them. But got caught up in other things before checking them out, and when I was about to, wife called, being hungry. Me too. So I posted the post and went for dinner

Urs · Post by **Urs** » Thu Dec 15, 2011 10:30 pm

jumpercable wrote:In ableton Live 8.2.7
Osx 10.6.8

Load the Diva AU
Delete
Load the Diva Vst
Delete
Load the Diva AU - the gui wont reappear for the AU. Not until you restart ableton.

That's a Cocoa problem on Mac. All our Cocoa-enabled AUs do that when you also open any corresponding VST. I've figured out a workaround, but haven't gotten around implementing it.

Urs · Post by **Urs** » Thu Dec 15, 2011 10:43 pm

hakey wrote:Don't know if this is a bug, but selecting 'analog1' for the triangle shape in the Dual VCO seems to change the sound of all waveshapes - the saw is slightly rounded, the sine squarish, the triangle closer to a sine, and all are slightly attenuated.

I think it's a misnomer, not a bug. /Meneeds to ask Clemens, he had to do that VCO all by himself...

Urs · Post by **Urs** » Thu Dec 15, 2011 10:47 pm

Howard wrote:(BTW I wish all those modules already had a single, simple name each!)

Jajaja. Maybe.

hakey · Post by **hakey** » Thu Dec 15, 2011 10:55 pm

Urs wrote:I think it's a misnomer, not a bug. /Meneeds to ask Clemens, he had to do that VCO all by himself...

Ah, okay.

Audiority · Post by **Audiority** » Fri Dec 16, 2011 8:51 pm

don't know is somebody else already posted that but i found the following in the last beta:

[tested on OSX 10.6.8, Ableton Suite 8.2.7, both VST and AU]

- keyboard tracking on filters is not working at all
- sync is not working properly: when you change slave oscillator pitch, there isn't any timbre change.

if feature requests are allowed, it would be nice to have a keyboard tracking parameter at least for the oscillators that will be sync slaves.

Cheers,
Luca

hakey · Post by **hakey** » Fri Dec 16, 2011 9:01 pm

ZioAxiom wrote:- keyboard tracking on filters is not working at all
- sync is not working properly: when you change slave oscillator pitch, there isn't any timbre change.

Both working fine here (WinXP Live 8.1.4).

Key tracking at 100%? Filter feedback off?

Triple osc slave volume not turned up?

jumpercable · Post by **jumpercable** » Sat Dec 17, 2011 1:34 am

Not sure if bug - using a single sine wave in dual vco on vco2 - if you change it to "draft" you get some crazy weird high frequency thing. Most noticeable on lower notes.

Urs · Post by **Urs** » Sat Dec 17, 2011 2:13 am

jumpercable wrote:Not sure if bug - using a single sine wave in dual vco on vco2 - if you change it to "draft" you get some crazy weird high frequency thing. Most noticeable on lower notes.

That's probably aliasing... draft isn't all that oversampled... I'll have a listen tomorrow anyway!

u-he

KVR Audio

DIVA known issues