u-he

Mr D · Post by **Mr D** » Tue May 08, 2012 9:52 am

Hi,

Say i want to make a patch that consists of two very similar (but slightly different oscillators. Is there any way for me to first make one OSC, then copy (or duplicate) it? That would be easier then having to set up the second OSC with the same parameters.

I guess the same question applies to LFOs and envelopes..........any way to copy the setting of LFO 1 to LFO 2 (for example)?

Thanks!

hakey · Post by **hakey** » Tue May 08, 2012 10:09 am

Save the oscillator as an oscillator preset: open, eg, Osc1 tab in the bottom section > right click in the Oscillator Module Preset box > select "save oscillator settings" > open, eg, Osc2 tab and select your saved preset.

Howard · Post by **Howard** » Tue May 08, 2012 10:11 am

Go to the "Osc 1" tab, right click on "Oscillator Module Preset", select "save Oscillator1 settings", name as "...". Create oscillator 2, go to the "Osc 2" tab and load "..." from the same button.

BTW I always use "..." for temporary oscillators.

Edit: Hakey beat me to it again!

hakey · Post by **hakey** » Tue May 08, 2012 10:21 am

Howard wrote:Edit: Hakey beat me to it again!

(again?)

Mr D · Post by **Mr D** » Tue May 08, 2012 10:36 am

Thanks a lot!

I'm guessing there's no way to duplicate LFOs and envelopes?!

Urs · Post by **Urs** » Tue May 08, 2012 10:43 am

Not yet, but it's a common feature request. We may at some day get it done!

EvilDragon · Post by **EvilDragon** » Tue May 08, 2012 10:52 am

To me it kinda makes sense to Ctrl+drag out a module to copy it...

Mr D · Post by **Mr D** » Tue May 08, 2012 10:56 am

EvilDragon wrote:To me it kinda makes sense to Ctrl+drag out a module to copy it...

Yes indeed, and if you Ctrl+drag to an existing module, it'll copy the settings to that one!

Mr D · Post by **Mr D** » Tue May 08, 2012 11:10 am

Just another quick question:

LFO 1 is hard wired to vibrato, right?

But say i don't want any vibrato and want to free up this LFO?!

I don't see anywhere to cancel this modulation routing.

Any ideas?

Urs · Post by **Urs** » Tue May 08, 2012 11:52 am

Mr D wrote:Just another quick question:

LFO 1 is hard wired to vibrato, right?

But say i don't want any vibrato and want to free up this LFO?!

I don't see anywhere to cancel this modulation routing.

Any ideas?

You can set Vibrato to 0.00 and use other Modulation Slots / ModMatrix to do oscillator tune modulation...

Mr D · Post by **Mr D** » Tue May 08, 2012 12:16 pm

Of course, i was being a dumb-ass! - thanks!

Mr D · Post by **Mr D** » Tue May 08, 2012 12:20 pm

I'm messing around with the MSEGs........they're fantastic!

Here's a couple of feature requests: The ability to define a fixed number of loops before it moves to the release.

And......the ability to modulate the vertical value of envelope points! (ok, so i know it's unlikely you'd do that, but it's worth a try!)

Urs · Post by **Urs** » Tue May 08, 2012 12:23 pm

I was thinking of adding an optional D-Point, and a method to compress the loop upwards or downwards. Then we can add normal ADSR controls to MSEGs, which may possibly be modulation targets.

hakey · Post by **hakey** » Tue May 08, 2012 1:07 pm

Global mode for MSEGs?

Howard · Post by **Howard** » Tue May 08, 2012 1:22 pm

hakey wrote:Global mode for MSEGs?

"Single" isn't enough?

u-he

KVR Audio

Zebra: Any way to duplicate oscillators, envelopes, LFO etc