u-he

Sendy · Post by **Sendy** » Tue Apr 15, 2014 9:46 pm

Some faint lines showing where each bar of the graph begins/ends would be really helpful for constructing certain functions. For example I'm currently trying to produce one which is two interleaved ramps, asin -1, 1, -0.9, 0.9, -0.8, etc. It's quite the task

Also, this part of ACE could really use preset support, though at the moment I'm thankful for being able to copy and paste from preset to preset.

Howard · Post by **Howard** » Wed Apr 16, 2014 1:48 am

Sendy wrote:...I'm currently trying to produce one which is two interleaved ramps, asin -1, 1, -0.9, 0.9, -0.8, etc. It's quite the task

Wait a week or two, Sendy - that's dead easy in the latest beta.

pdxindy · Post by **pdxindy** » Wed Apr 16, 2014 2:29 am

ACE-Ramp.jpg

Like this? I just did that in like 6 seconds... go get the latest beta (v2242). It has a number of excellent new functions for the Mapper!

Sendy · Post by **Sendy** » Wed Apr 16, 2014 5:14 pm

Ohh, nice. I'll go check it out

pdxindy · Post by **pdxindy** » Wed Apr 16, 2014 5:18 pm

Sendy wrote:Ohh, nice. I'll go check it out

These new functions are also in the Zebra ModMappers and the LFO's on user mode!!

Sendy · Post by **Sendy** » Wed Apr 16, 2014 5:39 pm

Wait... where/how do I download betas?

I'm sure I've done this before but I can't find it.

Biscotto · Post by **Biscotto** » Wed Apr 16, 2014 5:43 pm

Sendy wrote:Wait... where/how do I download betas?

I'm sure I've done this before but I can't find it.

http://www.kvraudio.com/forum/viewtopic ... 3#p5715583

pdxindy · Post by **pdxindy** » Wed Apr 16, 2014 5:51 pm

ACE-Mapper.jpg

Another quick example...

Sendy · Post by **Sendy** » Wed Apr 16, 2014 5:57 pm

Sexy

Sendy · Post by **Sendy** » Wed Apr 16, 2014 5:57 pm

Biscotto wrote:
Sendy wrote:Wait... where/how do I download betas?

I'm sure I've done this before but I can't find it.
http://www.kvraudio.com/forum/viewtopic ... 3#p5715583

Thanks.

Biscotto · Post by **Biscotto** » Wed Apr 16, 2014 10:19 pm

You're welcome.
People wake up with the weather report page, I wake up to the u-he forum page

Sendy · Post by **Sendy** » Wed Apr 16, 2014 10:39 pm

I'm loving the new controls... I may not even need lines seperating each bar now.

And now we can turn off the highpass filter on the output, that's neat, since it makes the waveform more coherent on an external oscilloscope. Plus sometimes filters can mess with the crest factor of the output.

pdxindy · Post by **pdxindy** » Wed Apr 16, 2014 11:44 pm

Sendy wrote:I'm loving the new controls... I may not even need lines seperating each bar now.

And now we can turn off the highpass filter on the output, that's neat, since it makes the waveform more coherent on an external oscilloscope. Plus sometimes filters can mess with the crest factor of the output.

How do you turn off the highpass filter on the output?

Sendy · Post by **Sendy** » Thu Apr 17, 2014 12:23 am

pdxindy wrote:
Sendy wrote:I'm loving the new controls... I may not even need lines seperating each bar now.

And now we can turn off the highpass filter on the output, that's neat, since it makes the waveform more coherent on an external oscilloscope. Plus sometimes filters can mess with the crest factor of the output.
How do you turn off the highpass filter on the output?

It happens when you turn off the effects section.

pdxindy · Post by **pdxindy** » Thu Apr 17, 2014 1:48 am

Sendy wrote:
pdxindy wrote:
Sendy wrote:I'm loving the new controls... I may not even need lines seperating each bar now.

And now we can turn off the highpass filter on the output, that's neat, since it makes the waveform more coherent on an external oscilloscope. Plus sometimes filters can mess with the crest factor of the output.
How do you turn off the highpass filter on the output?
It happens when you turn off the effects section.

Thanks... btw, the same improvements are there in the Zebra LFO's... They are suddenly much more capable! (in the practical sense)

u-he

KVR Audio

ACE mapping generator visual guides