.../s~[FR] Add a LU custom reference in LoudnessAnalizer
-
- KVRian
- 915 posts since 2 May, 2015
...whoooaa DS...u lookin' fo' a job?...sooooooooo +++++++ on that request...if that "display" makes the light of day it should top all the "questions"...and might/would make MLA the best 2bus analyzer out there...and god knows i have enough of them... .../s~
.../s~mba m2 15" | 16gig.ram | 1tb ssd | macOS 26.1 Tahoe
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
-
MeldaProduction MeldaProduction https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=176122 - KVRAF
- 14339 posts since 15 Mar, 2008 from Czech republic
I'll check. Probably nothing for the timegraphs though...
-
- KVRian
- 915 posts since 2 May, 2015
...well, I guess that answers that question...at about 9:22 this am... 
.../s~
.../s~mba m2 15" | 16gig.ram | 1tb ssd | macOS 26.1 Tahoe
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
-
- KVRAF
- 10374 posts since 2 Sep, 2003 from Surrey, UK
Question:
Are there any non-integral reference levels? All the ones that I've seen are integer numbers (-23, -20, -14 ,-12 etc)
Are there any non-integral reference levels? All the ones that I've seen are integer numbers (-23, -20, -14 ,-12 etc)
-
- KVRist
- Topic Starter
- 55 posts since 6 Dec, 2012
(finally some free time !)
I think add a target making 0 = -(something)LUFS would not work, because the "target" level of Short term, momentary and integrated aren't the same
I think add a target making 0 = -(something)LUFS would not work, because the "target" level of Short term, momentary and integrated aren't the same
-
MeldaProduction MeldaProduction https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=176122
- KVRAF
- 14339 posts since 15 Mar, 2008 from Czech republic
Well, if you need 2 different target levels, you can always use 2 instancesdistante wrote:(finally some free time !)
I think add a target making 0 = -(something)LUFS would not work, because the "target" level of Short term, momentary and integrated aren't the same
. But I'm quite surprised there is "target level for shortterm or even momentary" loudness, doesn't make sense to me. Who defines that?-
- KVRist
- Topic Starter
- 55 posts since 6 Dec, 2012
Well normally there's just integrate guidelines regarding the main end (youtube,spotify,itunes,etc) the other two depends of the kind of work, sometimes you can have a "max hot level" of XdBFS.
The other stuff (in music at least) is the PLR but that is other history!
The other stuff (in music at least) is the PLR but that is other history!
-
- KVRian
- 915 posts since 2 May, 2015
...indeed, "the PLR but that is another history(story)!"...it would be nice if that value were calculated and shown as well, beneath the "integrated" numerical display at the right end of the meter...but I'm afraid to ask for it just now...
.../s~
.../s~mba m2 15" | 16gig.ram | 1tb ssd | macOS 26.1 Tahoe
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
)-
- KVRian
- 915 posts since 2 May, 2015
...no worries...you don't need to learn German to have bad American/English...just watch some of our politicians on tv...incarnate, I say! incarnate... .../s~
.../s~mba m2 15" | 16gig.ram | 1tb ssd | macOS 26.1 Tahoe
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
logic 11.2.2 | reaper 7.75 | cubase 14.0.4
focusrite.2i2 | A&H CQ18t
-
- KVRAF
- 10374 posts since 2 Sep, 2003 from Surrey, UK
^^^^
I use the Limit value for that.
Here is a -17dB signal:
its peaks shows as -17dB, and the LU meters shows 6 LU (compared with the target value of -23 dB. I have set the Limit to 4 dB, so anything between -4 and 4 LU is OK and shown in green on the meters, but anything over 4 LU is not good and is shown in red.
I use the Limit value for that.
Here is a -17dB signal:
its peaks shows as -17dB, and the LU meters shows 6 LU (compared with the target value of -23 dB. I have set the Limit to 4 dB, so anything between -4 and 4 LU is OK and shown in green on the meters, but anything over 4 LU is not good and is shown in red.