Can someone tell me what is error 34 and how to fix it.
ERROR 34
"GRUB mis-configured"
Drive is configured for a different hardware platform
Thank you
Mac
ERROR 34
-
- KVRer
- 20 posts since 16 Aug, 2015 from Chicago
Hello,
Can someone tell me what is error 34 and how to fix it.
ERROR 34
"GRUB mis-configured"
Drive is configured for a different hardware platform
Thank you
Mac
Can someone tell me what is error 34 and how to fix it.
ERROR 34
"GRUB mis-configured"
Drive is configured for a different hardware platform
Thank you
Mac
-
- KVRist
- 144 posts since 20 Feb, 2013
Hello
Grub is the Bootloader that "loads" linux in the case of the receptor.
The error code indicates that there is a problem loading the correct linux config on your receptor.
If you are going to try to change anything in grub make a backup of "boot/grub/menu.lst"
Before you start also backup the receptors hard drive . Here is a Link explaining exactly what grub is and what it does and what you can do to fix problems with it.http://www.dedoimedo.com/computers/grub.html if you dont like messing with your Receptors software let someone who knows linux and grub do It for you ,grub can be reinstalled.
Good luck Andy
Grub is the Bootloader that "loads" linux in the case of the receptor.
The error code indicates that there is a problem loading the correct linux config on your receptor.
If you are going to try to change anything in grub make a backup of "boot/grub/menu.lst"
Before you start also backup the receptors hard drive . Here is a Link explaining exactly what grub is and what it does and what you can do to fix problems with it.http://www.dedoimedo.com/computers/grub.html if you dont like messing with your Receptors software let someone who knows linux and grub do It for you ,grub can be reinstalled.
Good luck Andy
-
- KVRer
- Topic Starter
- 20 posts since 16 Aug, 2015 from Chicago
Hi Andy,
This is way beyond my knowledge. I never had this problem before. I use Digital Performer 9 on a iMac 5.
When I turn on VIP2 it says "Problem Found 34" and press for Support Tool, Support self-test Check All? Press. It runs a self-test, all test then returns "Error 34.
Mac
This is way beyond my knowledge. I never had this problem before. I use Digital Performer 9 on a iMac 5.
When I turn on VIP2 it says "Problem Found 34" and press for Support Tool, Support self-test Check All? Press. It runs a self-test, all test then returns "Error 34.
Mac
-
- KVRist
- 144 posts since 20 Feb, 2013
hi
Does the receptor work appart from Showing the error code??
or does it load after the error code.
have you tried opening the receptor and checking that all the conectors are in place especialy the hard drive and front panel connectors.
andy
Does the receptor work appart from Showing the error code??
or does it load after the error code.
have you tried opening the receptor and checking that all the conectors are in place especialy the hard drive and front panel connectors.
andy
-
- KVRer
- Topic Starter
- 20 posts since 16 Aug, 2015 from Chicago
It loads after I shut down and start up a few times.
I do the support tool check and it stills gives me the error 34
I do the support tool check and it stills gives me the error 34
-
- KVRer
- Topic Starter
- 20 posts since 16 Aug, 2015 from Chicago
Hardware check gives the Error 34
-
- KVRAF
- 16800 posts since 8 Mar, 2005 from Utrecht, Holland
Checking connectors won't do any good since the boot loader is f$%^ked up and that piece of software needs to be reinstalled. Maybe you can format the drive again (and lose all data stored on it) or indeed make contact with a linux geek somewhere that can reinstall GRUB.
Also out of courtesy plz visit the other topic: viewtopic.php?f=74&t=463923
Also out of courtesy plz visit the other topic: viewtopic.php?f=74&t=463923
We are the KVR collective. Resistance is futile. You will be assimilated. 
My MusicCalc is served over https!!
My MusicCalc is served over https!!
-
- KVRist
- 144 posts since 20 Feb, 2013
Hi
The error codes that the receptor generates are not all ways reliable i have myself experienced an error 34 allong with a load of other errors .
These where genarated dur to a bad connection between the Mb and hdd that is why i suggest that you check the cables before going to the next stage.
Regards Andy
The error codes that the receptor generates are not all ways reliable i have myself experienced an error 34 allong with a load of other errors .
These where genarated dur to a bad connection between the Mb and hdd that is why i suggest that you check the cables before going to the next stage.
Regards Andy
-
- KVRist
- 229 posts since 6 May, 2014 from New Mexico
The following is from a table format in the Plugorama site. The copy/ paste of the table didn't format so well in this forum entry so just click on the link.
https://www.plugorama.com/kb.php?id=499
ERROR CODE VGA MESSAGE POSSIBLE CAUSES
ERROR 1
"Program called with invalid arguments"
Bad system software
ERROR 2
"Audio device cannot be
found"
Audio device driver not loading, (check audio board connections).
ERROR 3
"lmsupport is not
installed"
Sensor package for motherboard not installed
ERROR 4
"Motherboard has no
temperature sensors"
Different motherboard than expected
ERROR 5
"Motherboard temperature is too high"
CPU temp is reporting higher than normal. Check system fan.
ERROR 6
"Unable to open audio
device at specified rate and/or depth"
Cable from USB port to audio board is disconnected, audio board firmware not programmed, or board not powered properly.
ERROR 7
"Audio device does not have expected mixer controls"
Audio device reports being busy (software error) or wrong audio board installed.
ERROR 8
"CompactFlash reader not found"
CF card reader not plugged in (depends on configuration)
ERROR 9
"WINE dosdevices are
incorrect"
Bad system software
ERROR 10
"RPM verification
failed: operating system may be corrupt"
Bad update module or software update problem.
ERROR 12
"Hyperthreading
enabled: may negatively impact performance"
BIOS settings are incorrect.
ERROR 13
"Ethernet device eth0 not available"
BIOS settings incorrect , Bad Motherboard Ethernet NIC
ERROR 14
"Networking status does not match status file"
Networking not configuring correctly. Check BIOS and System software
ERROR 15
"Networking up but
services not started"
Bad System Software.
ERROR 16
"Firewall is misconfigured: some services may be unavailable"
Bad System Software.
ERROR 17
"Security risk: network address is not a LAN address"
Router that unit is connected to is not configured correctly, or there is no DHCP router on the network
ERROR 18
"Incorrect amount of
RAM installed"
MuseBox only: must have 2GB memory minimum installed.
ERROR 19
"USB not configured
correctly"
Possibly bad motherboard.
ERROR 20
"Multiple devices have failed HWOK test"
Run tests one by one to verify. May indicate bad motherboard.
ERROR 21
"Internal MIDI OSS device not found"
Front panel MIDI port not detected, bad cable, board or firmware.
ERROR 22
"Internal MIDI device not found"
Front panel MIDI port not detected, bad cable, board or firmware
ERROR 23
X has failed with an error (fatal error):
Bad system software, or bad BIOS version.
ERROR 24
"X server could not be started"
Bad system software or bad BIOS version.
ERROR 25
"System fan too slow. Random shutdowns or crashes may occur"
MuseBox only: Check or replace System Fan or check BIOS Fan settings.
ERROR 26
"System fan unsteady (max-min range too large)"
MuseBox: Check or replace System Fan or check BIOS fan settings.
ERROR 27
"Internal drive is the
wrong size"
Drive is incorrect for system software version.
ERROR 28
"Internal drive is too slow"
Drive is not meeting minimum speed specifications.
ERROR 29
"BIOS version is too old";
Update Motherboard BIOS
ERROR 30
"The system could not be updated"
System Software Problem - contact Muse Research.
ERROR 31
"The system is not up to
date. Check for updates using duohost."
Newer system software is available, download and update.
ERROR 32
"Fan Has Not Yet Been Calibrated Via Support Tools"
MuseBox only: System Fan Needs Calibration, go to support tools, select Expert Mode, calibrate fan
ERROR 33
"VST RPM verification failed"
Plugin not installed correctly. Download again and re-install
ERROR 34
"GRUB mis-configured"
Drive is configured for a different hardware platform
ERROR 127
"Generic Error Code"
Problem of unknown source; likely an improperly configured drive
ERROR 137
"Process Killed"
Plug-in host has been forced closed by a reboot or shutdown command.
ERROR 139
"Process has Crashed"
Host has been crashed by a process, most likely a bug in the plug-in.
ERROR 1000
"Z Server could not be started"
Bad system software.
ERROR 1001
"Metacity window manager could not be started"
Bad system software.
ERROR 2000
"The X server is not running"
Bad system software.
ERROR 2001
"The rdm session program failed to start"
Bad system software.
ERROR 4000
"General fatal error,
details in system log"
Bad system software.
ERROR 4001
"Audio device won't
open but rdm-run-test is clean"
System software cannot open the audio device although it is detected.
ERROR 4002
"Primary MIDI device
won't open but rdm-run-test is clean"
System software cannot open the MIDi device although it is detected
ERROR 4003
"IPC between host-engine and duo-host has failed. Rebooting may help"
MuseBox only: System software has crashed. Reboot.
ERROR 4004
"The versions of duo-host and host-engine do not match. Installation error"
MuseBox only: Bad software update or software installation. Get new update and install again.
ERROR 4005
"General fatal error when starting the host-engine; details in system log"
MuseBox only: Bad system software. Could also indicate hardware problem.
ERROR 4006
"Playback is stuck and
must be reset"
MuseBox only: System software has crashed.
ERROR 4007
"Fatal program error in
host-engine or plugin code"
MuseBox only: System software has crashed.
ERROR 4008
"The host-engine quit
unexpectedly and must be restarted"
MuseBox only: System software has crashed.
ERROR 4009
"Audio hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4001. Check system software and audio board.
ERROR 4010
"MIDI hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4002. Check system software and front panel board.
ERROR 4011
"The startup file could
not be loaded; restart with default patch"
MuseBox only: Bad or corrupt the patched saved on shutdown, unit might have been shut down improperly.
ERROR 4012
"The primary MIDI device could not be opened; running with USB MIDI only"
Notifcation that MIDI device cannot be used. Check front panel board connection and MIDI firmware
https://www.plugorama.com/kb.php?id=499
ERROR CODE VGA MESSAGE POSSIBLE CAUSES
ERROR 1
"Program called with invalid arguments"
Bad system software
ERROR 2
"Audio device cannot be
found"
Audio device driver not loading, (check audio board connections).
ERROR 3
"lmsupport is not
installed"
Sensor package for motherboard not installed
ERROR 4
"Motherboard has no
temperature sensors"
Different motherboard than expected
ERROR 5
"Motherboard temperature is too high"
CPU temp is reporting higher than normal. Check system fan.
ERROR 6
"Unable to open audio
device at specified rate and/or depth"
Cable from USB port to audio board is disconnected, audio board firmware not programmed, or board not powered properly.
ERROR 7
"Audio device does not have expected mixer controls"
Audio device reports being busy (software error) or wrong audio board installed.
ERROR 8
"CompactFlash reader not found"
CF card reader not plugged in (depends on configuration)
ERROR 9
"WINE dosdevices are
incorrect"
Bad system software
ERROR 10
"RPM verification
failed: operating system may be corrupt"
Bad update module or software update problem.
ERROR 12
"Hyperthreading
enabled: may negatively impact performance"
BIOS settings are incorrect.
ERROR 13
"Ethernet device eth0 not available"
BIOS settings incorrect , Bad Motherboard Ethernet NIC
ERROR 14
"Networking status does not match status file"
Networking not configuring correctly. Check BIOS and System software
ERROR 15
"Networking up but
services not started"
Bad System Software.
ERROR 16
"Firewall is misconfigured: some services may be unavailable"
Bad System Software.
ERROR 17
"Security risk: network address is not a LAN address"
Router that unit is connected to is not configured correctly, or there is no DHCP router on the network
ERROR 18
"Incorrect amount of
RAM installed"
MuseBox only: must have 2GB memory minimum installed.
ERROR 19
"USB not configured
correctly"
Possibly bad motherboard.
ERROR 20
"Multiple devices have failed HWOK test"
Run tests one by one to verify. May indicate bad motherboard.
ERROR 21
"Internal MIDI OSS device not found"
Front panel MIDI port not detected, bad cable, board or firmware.
ERROR 22
"Internal MIDI device not found"
Front panel MIDI port not detected, bad cable, board or firmware
ERROR 23
X has failed with an error (fatal error):
Bad system software, or bad BIOS version.
ERROR 24
"X server could not be started"
Bad system software or bad BIOS version.
ERROR 25
"System fan too slow. Random shutdowns or crashes may occur"
MuseBox only: Check or replace System Fan or check BIOS Fan settings.
ERROR 26
"System fan unsteady (max-min range too large)"
MuseBox: Check or replace System Fan or check BIOS fan settings.
ERROR 27
"Internal drive is the
wrong size"
Drive is incorrect for system software version.
ERROR 28
"Internal drive is too slow"
Drive is not meeting minimum speed specifications.
ERROR 29
"BIOS version is too old";
Update Motherboard BIOS
ERROR 30
"The system could not be updated"
System Software Problem - contact Muse Research.
ERROR 31
"The system is not up to
date. Check for updates using duohost."
Newer system software is available, download and update.
ERROR 32
"Fan Has Not Yet Been Calibrated Via Support Tools"
MuseBox only: System Fan Needs Calibration, go to support tools, select Expert Mode, calibrate fan
ERROR 33
"VST RPM verification failed"
Plugin not installed correctly. Download again and re-install
ERROR 34
"GRUB mis-configured"
Drive is configured for a different hardware platform
ERROR 127
"Generic Error Code"
Problem of unknown source; likely an improperly configured drive
ERROR 137
"Process Killed"
Plug-in host has been forced closed by a reboot or shutdown command.
ERROR 139
"Process has Crashed"
Host has been crashed by a process, most likely a bug in the plug-in.
ERROR 1000
"Z Server could not be started"
Bad system software.
ERROR 1001
"Metacity window manager could not be started"
Bad system software.
ERROR 2000
"The X server is not running"
Bad system software.
ERROR 2001
"The rdm session program failed to start"
Bad system software.
ERROR 4000
"General fatal error,
details in system log"
Bad system software.
ERROR 4001
"Audio device won't
open but rdm-run-test is clean"
System software cannot open the audio device although it is detected.
ERROR 4002
"Primary MIDI device
won't open but rdm-run-test is clean"
System software cannot open the MIDi device although it is detected
ERROR 4003
"IPC between host-engine and duo-host has failed. Rebooting may help"
MuseBox only: System software has crashed. Reboot.
ERROR 4004
"The versions of duo-host and host-engine do not match. Installation error"
MuseBox only: Bad software update or software installation. Get new update and install again.
ERROR 4005
"General fatal error when starting the host-engine; details in system log"
MuseBox only: Bad system software. Could also indicate hardware problem.
ERROR 4006
"Playback is stuck and
must be reset"
MuseBox only: System software has crashed.
ERROR 4007
"Fatal program error in
host-engine or plugin code"
MuseBox only: System software has crashed.
ERROR 4008
"The host-engine quit
unexpectedly and must be restarted"
MuseBox only: System software has crashed.
ERROR 4009
"Audio hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4001. Check system software and audio board.
ERROR 4010
"MIDI hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4002. Check system software and front panel board.
ERROR 4011
"The startup file could
not be loaded; restart with default patch"
MuseBox only: Bad or corrupt the patched saved on shutdown, unit might have been shut down improperly.
ERROR 4012
"The primary MIDI device could not be opened; running with USB MIDI only"
Notifcation that MIDI device cannot be used. Check front panel board connection and MIDI firmware
Fish Out Of Water
Entune Productions
Entune Productions
-
- KVRist
- 229 posts since 6 May, 2014 from New Mexico
The following is from a table format in the Plugorama site. The copy/ paste of the table didn't format so well in this forum entry so just click on the link.
https://www.plugorama.com/kb.php?id=499
ERROR CODE VGA MESSAGE POSSIBLE CAUSES
ERROR 1
"Program called with invalid arguments"
Bad system software
ERROR 2
"Audio device cannot be
found"
Audio device driver not loading, (check audio board connections).
ERROR 3
"lmsupport is not
installed"
Sensor package for motherboard not installed
ERROR 4
"Motherboard has no
temperature sensors"
Different motherboard than expected
ERROR 5
"Motherboard temperature is too high"
CPU temp is reporting higher than normal. Check system fan.
ERROR 6
"Unable to open audio
device at specified rate and/or depth"
Cable from USB port to audio board is disconnected, audio board firmware not programmed, or board not powered properly.
ERROR 7
"Audio device does not have expected mixer controls"
Audio device reports being busy (software error) or wrong audio board installed.
ERROR 8
"CompactFlash reader not found"
CF card reader not plugged in (depends on configuration)
ERROR 9
"WINE dosdevices are
incorrect"
Bad system software
ERROR 10
"RPM verification
failed: operating system may be corrupt"
Bad update module or software update problem.
ERROR 12
"Hyperthreading
enabled: may negatively impact performance"
BIOS settings are incorrect.
ERROR 13
"Ethernet device eth0 not available"
BIOS settings incorrect , Bad Motherboard Ethernet NIC
ERROR 14
"Networking status does not match status file"
Networking not configuring correctly. Check BIOS and System software
ERROR 15
"Networking up but
services not started"
Bad System Software.
ERROR 16
"Firewall is misconfigured: some services may be unavailable"
Bad System Software.
ERROR 17
"Security risk: network address is not a LAN address"
Router that unit is connected to is not configured correctly, or there is no DHCP router on the network
ERROR 18
"Incorrect amount of
RAM installed"
MuseBox only: must have 2GB memory minimum installed.
ERROR 19
"USB not configured
correctly"
Possibly bad motherboard.
ERROR 20
"Multiple devices have failed HWOK test"
Run tests one by one to verify. May indicate bad motherboard.
ERROR 21
"Internal MIDI OSS device not found"
Front panel MIDI port not detected, bad cable, board or firmware.
ERROR 22
"Internal MIDI device not found"
Front panel MIDI port not detected, bad cable, board or firmware
ERROR 23
X has failed with an error (fatal error):
Bad system software, or bad BIOS version.
ERROR 24
"X server could not be started"
Bad system software or bad BIOS version.
ERROR 25
"System fan too slow. Random shutdowns or crashes may occur"
MuseBox only: Check or replace System Fan or check BIOS Fan settings.
ERROR 26
"System fan unsteady (max-min range too large)"
MuseBox: Check or replace System Fan or check BIOS fan settings.
ERROR 27
"Internal drive is the
wrong size"
Drive is incorrect for system software version.
ERROR 28
"Internal drive is too slow"
Drive is not meeting minimum speed specifications.
ERROR 29
"BIOS version is too old";
Update Motherboard BIOS
ERROR 30
"The system could not be updated"
System Software Problem - contact Muse Research.
ERROR 31
"The system is not up to
date. Check for updates using duohost."
Newer system software is available, download and update.
ERROR 32
"Fan Has Not Yet Been Calibrated Via Support Tools"
MuseBox only: System Fan Needs Calibration, go to support tools, select Expert Mode, calibrate fan
ERROR 33
"VST RPM verification failed"
Plugin not installed correctly. Download again and re-install
ERROR 34
"GRUB mis-configured"
Drive is configured for a different hardware platform
ERROR 127
"Generic Error Code"
Problem of unknown source; likely an improperly configured drive
ERROR 137
"Process Killed"
Plug-in host has been forced closed by a reboot or shutdown command.
ERROR 139
"Process has Crashed"
Host has been crashed by a process, most likely a bug in the plug-in.
ERROR 1000
"Z Server could not be started"
Bad system software.
ERROR 1001
"Metacity window manager could not be started"
Bad system software.
ERROR 2000
"The X server is not running"
Bad system software.
ERROR 2001
"The rdm session program failed to start"
Bad system software.
ERROR 4000
"General fatal error,
details in system log"
Bad system software.
ERROR 4001
"Audio device won't
open but rdm-run-test is clean"
System software cannot open the audio device although it is detected.
ERROR 4002
"Primary MIDI device
won't open but rdm-run-test is clean"
System software cannot open the MIDi device although it is detected
ERROR 4003
"IPC between host-engine and duo-host has failed. Rebooting may help"
MuseBox only: System software has crashed. Reboot.
ERROR 4004
"The versions of duo-host and host-engine do not match. Installation error"
MuseBox only: Bad software update or software installation. Get new update and install again.
ERROR 4005
"General fatal error when starting the host-engine; details in system log"
MuseBox only: Bad system software. Could also indicate hardware problem.
ERROR 4006
"Playback is stuck and
must be reset"
MuseBox only: System software has crashed.
ERROR 4007
"Fatal program error in
host-engine or plugin code"
MuseBox only: System software has crashed.
ERROR 4008
"The host-engine quit
unexpectedly and must be restarted"
MuseBox only: System software has crashed.
ERROR 4009
"Audio hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4001. Check system software and audio board.
ERROR 4010
"MIDI hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4002. Check system software and front panel board.
ERROR 4011
"The startup file could
not be loaded; restart with default patch"
MuseBox only: Bad or corrupt the patched saved on shutdown, unit might have been shut down improperly.
ERROR 4012
"The primary MIDI device could not be opened; running with USB MIDI only"
Notifcation that MIDI device cannot be used. Check front panel board connection and MIDI firmware
https://www.plugorama.com/kb.php?id=499
ERROR CODE VGA MESSAGE POSSIBLE CAUSES
ERROR 1
"Program called with invalid arguments"
Bad system software
ERROR 2
"Audio device cannot be
found"
Audio device driver not loading, (check audio board connections).
ERROR 3
"lmsupport is not
installed"
Sensor package for motherboard not installed
ERROR 4
"Motherboard has no
temperature sensors"
Different motherboard than expected
ERROR 5
"Motherboard temperature is too high"
CPU temp is reporting higher than normal. Check system fan.
ERROR 6
"Unable to open audio
device at specified rate and/or depth"
Cable from USB port to audio board is disconnected, audio board firmware not programmed, or board not powered properly.
ERROR 7
"Audio device does not have expected mixer controls"
Audio device reports being busy (software error) or wrong audio board installed.
ERROR 8
"CompactFlash reader not found"
CF card reader not plugged in (depends on configuration)
ERROR 9
"WINE dosdevices are
incorrect"
Bad system software
ERROR 10
"RPM verification
failed: operating system may be corrupt"
Bad update module or software update problem.
ERROR 12
"Hyperthreading
enabled: may negatively impact performance"
BIOS settings are incorrect.
ERROR 13
"Ethernet device eth0 not available"
BIOS settings incorrect , Bad Motherboard Ethernet NIC
ERROR 14
"Networking status does not match status file"
Networking not configuring correctly. Check BIOS and System software
ERROR 15
"Networking up but
services not started"
Bad System Software.
ERROR 16
"Firewall is misconfigured: some services may be unavailable"
Bad System Software.
ERROR 17
"Security risk: network address is not a LAN address"
Router that unit is connected to is not configured correctly, or there is no DHCP router on the network
ERROR 18
"Incorrect amount of
RAM installed"
MuseBox only: must have 2GB memory minimum installed.
ERROR 19
"USB not configured
correctly"
Possibly bad motherboard.
ERROR 20
"Multiple devices have failed HWOK test"
Run tests one by one to verify. May indicate bad motherboard.
ERROR 21
"Internal MIDI OSS device not found"
Front panel MIDI port not detected, bad cable, board or firmware.
ERROR 22
"Internal MIDI device not found"
Front panel MIDI port not detected, bad cable, board or firmware
ERROR 23
X has failed with an error (fatal error):
Bad system software, or bad BIOS version.
ERROR 24
"X server could not be started"
Bad system software or bad BIOS version.
ERROR 25
"System fan too slow. Random shutdowns or crashes may occur"
MuseBox only: Check or replace System Fan or check BIOS Fan settings.
ERROR 26
"System fan unsteady (max-min range too large)"
MuseBox: Check or replace System Fan or check BIOS fan settings.
ERROR 27
"Internal drive is the
wrong size"
Drive is incorrect for system software version.
ERROR 28
"Internal drive is too slow"
Drive is not meeting minimum speed specifications.
ERROR 29
"BIOS version is too old";
Update Motherboard BIOS
ERROR 30
"The system could not be updated"
System Software Problem - contact Muse Research.
ERROR 31
"The system is not up to
date. Check for updates using duohost."
Newer system software is available, download and update.
ERROR 32
"Fan Has Not Yet Been Calibrated Via Support Tools"
MuseBox only: System Fan Needs Calibration, go to support tools, select Expert Mode, calibrate fan
ERROR 33
"VST RPM verification failed"
Plugin not installed correctly. Download again and re-install
ERROR 34
"GRUB mis-configured"
Drive is configured for a different hardware platform
ERROR 127
"Generic Error Code"
Problem of unknown source; likely an improperly configured drive
ERROR 137
"Process Killed"
Plug-in host has been forced closed by a reboot or shutdown command.
ERROR 139
"Process has Crashed"
Host has been crashed by a process, most likely a bug in the plug-in.
ERROR 1000
"Z Server could not be started"
Bad system software.
ERROR 1001
"Metacity window manager could not be started"
Bad system software.
ERROR 2000
"The X server is not running"
Bad system software.
ERROR 2001
"The rdm session program failed to start"
Bad system software.
ERROR 4000
"General fatal error,
details in system log"
Bad system software.
ERROR 4001
"Audio device won't
open but rdm-run-test is clean"
System software cannot open the audio device although it is detected.
ERROR 4002
"Primary MIDI device
won't open but rdm-run-test is clean"
System software cannot open the MIDi device although it is detected
ERROR 4003
"IPC between host-engine and duo-host has failed. Rebooting may help"
MuseBox only: System software has crashed. Reboot.
ERROR 4004
"The versions of duo-host and host-engine do not match. Installation error"
MuseBox only: Bad software update or software installation. Get new update and install again.
ERROR 4005
"General fatal error when starting the host-engine; details in system log"
MuseBox only: Bad system software. Could also indicate hardware problem.
ERROR 4006
"Playback is stuck and
must be reset"
MuseBox only: System software has crashed.
ERROR 4007
"Fatal program error in
host-engine or plugin code"
MuseBox only: System software has crashed.
ERROR 4008
"The host-engine quit
unexpectedly and must be restarted"
MuseBox only: System software has crashed.
ERROR 4009
"Audio hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4001. Check system software and audio board.
ERROR 4010
"MIDI hardware could not be opened; must restart to retry"
MuseBox only: Driver did not load, similar to 4002. Check system software and front panel board.
ERROR 4011
"The startup file could
not be loaded; restart with default patch"
MuseBox only: Bad or corrupt the patched saved on shutdown, unit might have been shut down improperly.
ERROR 4012
"The primary MIDI device could not be opened; running with USB MIDI only"
Notifcation that MIDI device cannot be used. Check front panel board connection and MIDI firmware
Fish Out Of Water
Entune Productions
Entune Productions
-
- KVRer
- Topic Starter
- 20 posts since 16 Aug, 2015 from Chicago
Hello,
Just to give you all an update on ERROR 34; the Receptor VIP 2 does come on after letting it run. This took about 30 min (every time) (thank you Andy). I am waiting for my external drive so I can back up my drive.
But here is what is going on now, when I save a new setup on the VIP and quit and reopen it does not open up to what I saved (under Favorite & User). Plus the GUI is not showing the column (left side) which shows all the sounds "Favorites" and "User" so I can select it.
I was told that my monitor setting can effect how much is shown, but I only have 2 settings for changing the monitor viewing and it does not change.
Any thoughts or ideas?
I do not know if it is the hard drive or software. I will find out if it is the hard drive once I do a backup; but if it is the software how do I go about getting a clean VIP 2 software? I am told by Plugorama that they have no more techs!
Bernard
Just to give you all an update on ERROR 34; the Receptor VIP 2 does come on after letting it run. This took about 30 min (every time) (thank you Andy). I am waiting for my external drive so I can back up my drive.
But here is what is going on now, when I save a new setup on the VIP and quit and reopen it does not open up to what I saved (under Favorite & User). Plus the GUI is not showing the column (left side) which shows all the sounds "Favorites" and "User" so I can select it.
I was told that my monitor setting can effect how much is shown, but I only have 2 settings for changing the monitor viewing and it does not change.
Any thoughts or ideas?
I do not know if it is the hard drive or software. I will find out if it is the hard drive once I do a backup; but if it is the software how do I go about getting a clean VIP 2 software? I am told by Plugorama that they have no more techs!
Bernard