MWobbler parallel fillters
-
- KVRAF
- 2973 posts since 10 Sep, 2003 from Karlskoga, Stockholm, Sweden
Maybe im blind but is there an options to run the two filters in MWobbler in parallel?
-
MeldaProduction MeldaProduction https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=176122 - KVRAF
- 14339 posts since 15 Mar, 2008 from Czech republic
I'm afraid not, only serial. You can always simulate parallel using 2 MWobblers or in MXXX for example.
-
- KVRAF
- Topic Starter
- 2973 posts since 10 Sep, 2003 from Karlskoga, Stockholm, Sweden
I am ^_^
Ever since your MXXX video showing the feedback module (how could i have missed that one??!) im building lots in MXXX.
Since i have you here, i have a little FR. In MXXX where all the sound lanes go out, could there be a meter of some sort showing output level? Instead of moving an Analyzer around. A little green going to red dot next to the 1,2,3,4,5 and 6 maybe? With complex routings .. and even simple ones, it's easy to loose track on where all the audio is going and how much of it!
I feel i made a terrible job explaining! Sorry! Hopefully you understand what i mean though!
Ever since your MXXX video showing the feedback module (how could i have missed that one??!) im building lots in MXXX.
Since i have you here, i have a little FR. In MXXX where all the sound lanes go out, could there be a meter of some sort showing output level? Instead of moving an Analyzer around. A little green going to red dot next to the 1,2,3,4,5 and 6 maybe? With complex routings .. and even simple ones, it's easy to loose track on where all the audio is going and how much of it!
I feel i made a terrible job explaining! Sorry! Hopefully you understand what i mean though!
-
- KVRian
- 1094 posts since 23 Sep, 2006
Are you worried about overloads in the chain? I don't think you need to worry about it, Melda plugs run at 32 or 64 bit floating point internally (I forget), they are not going to distort. Just make sure the main output is sensible.
Last edited by vectorwarrior on Sat Aug 27, 2016 5:09 pm, edited 1 time in total.
-
MeldaProduction MeldaProduction https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=176122
- KVRAF
- 14339 posts since 15 Mar, 2008 from Czech republic
Exactly! If you have multiple outputs mixed the output peak level can actually be lower than the highest of the separate outputs.
-
- KVRAF
- Topic Starter
- 2973 posts since 10 Sep, 2003 from Karlskoga, Stockholm, Sweden
Overloads..? pfft. Not a bother to me! lol
It's just to help me see what modules outputs audio. For instance, in order to use feedback to create a delay as a send effect (ie no dry signal out) you need to put a module after where you set volume to 0. Unless, im doing something wrong of course. It would be reassuring to know that there's no audio coming through that lane. Once you start having several feedback loops with different effects it's hard to tell in what lanes all the audio is coming from. If you're modulating a filter and assign range to a multiparameter and then another module and then ... suddenly the signal is fully filtered out and you can't tell until you start bypassing the lanes or move an Analyzer around!
It's probably not an issue if you're very methodical. But im not..
It's just to help me see what modules outputs audio. For instance, in order to use feedback to create a delay as a send effect (ie no dry signal out) you need to put a module after where you set volume to 0. Unless, im doing something wrong of course. It would be reassuring to know that there's no audio coming through that lane. Once you start having several feedback loops with different effects it's hard to tell in what lanes all the audio is coming from. If you're modulating a filter and assign range to a multiparameter and then another module and then ... suddenly the signal is fully filtered out and you can't tell until you start bypassing the lanes or move an Analyzer around!
It's probably not an issue if you're very methodical. But im not..
-
- KVRian
- 1094 posts since 23 Sep, 2006
Ha ha, fair enough. It would be nice to get better insight into what's going on, but space is so tight on those modules!
-
MeldaProduction MeldaProduction https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=176122
- KVRAF
- 14339 posts since 15 Mar, 2008 from Czech republic
Yeah, I'd rather avoid that, it's already complex enough 
. And after all the analysis modules are exactly for that.
. And after all the analysis modules are exactly for that.-
- KVRAF
- 10375 posts since 2 Sep, 2003 from Surrey, UK
^^^^
Indeed, I find multiple MMultiAnayser instances, in MXXX or on host tracks, invaluable for tracking things down.
Indeed, I find multiple MMultiAnayser instances, in MXXX or on host tracks, invaluable for tracking things down.