Stereo loss with Zebra
-
- KVRist
- 470 posts since 11 Aug, 2005 from Canada
I have a patch I made up that has a ton of LFO modulation going on in it and though I have been working on a piece for a few days now using this sound, just today, for some unknown reason, after I've been playing the patch and work for a while, the damn stereo imaging and left side is getting lost. So when panned fully one side, all sound disappears. I checked everything to do with all pannings and can't see a single reason why this has happened. If I close the work and re-open it, the full stereo is there again until it disappears again. That's why I know it's not anything to do with my programming and when I open all automation to find possible sources of the problem again, there's nothing to indicate I have done anything with the Read/Write things. Anyone else encounter this issue? It's as if the one side of the amp has disappeared.I'm using Cubase artist 8.5 on a desktop if that makes any difference.
-
- KVRAF
- 3473 posts since 25 Apr, 2011
Never had this issue. But i would save the patch under a new name and start troubleshooting. Working your way back, starting by removing the fx modules.rockmachine wrote:I have a patch I made up that has a ton of LFO modulation going on in it and though I have been working on a piece for a few days now using this sound, just today, for some unknown reason, after I've been playing the patch and work for a while, the damn stereo imaging and left side is getting lost. So when panned fully one side, all sound disappears. I checked everything to do with all pannings and can't see a single reason why this has happened. If I close the work and re-open it, the full stereo is there again until it disappears again. That's why I know it's not anything to do with my programming and when I open all automation to find possible sources of the problem again, there's nothing to indicate I have done anything with the Read/Write things. Anyone else encounter this issue? It's as if the one side of the amp has disappeared.I'm using Cubase artist 8.5 on a desktop if that makes any difference.
-
- KVRist
- Topic Starter
- 470 posts since 11 Aug, 2005 from Canada
I couldn't figure out any reason for why this happened, so this morning, tried another tack. I removed the instance of Zebra while retaining the track data, then loaded a new Zebra and loaded the patch which I had saved and so far, it's not doing what I described yesterday, so here's hoping. So far, so good.
-
- KVRAF
- 3473 posts since 25 Apr, 2011
Weird. It could be one of those problems which occurs without any (simple) traceable causes...hopefully it won't occur again.rockmachine wrote:I couldn't figure out any reason for why this happened, so this morning, tried another tack. I removed the instance of Zebra while retaining the track data, then loaded a new Zebra and loaded the patch which I had saved and so far, it's not doing what I described yesterday, so here's hoping. So far, so good.
-
Perimeter Sound Perimeter Sound https://www.kvraudio.com/forum/memberlist.php?mode=viewprofile&u=162713 - KVRAF
- 1745 posts since 11 Oct, 2007
Accidental midi learn of some kind ? Phasing issues ? No idea really....
-
- KVRist
- 148 posts since 1 Aug, 2004 from Germany
Does this patch rely heavily on the noise module in digital mode by any chance? I had a very similar problem some days ago where whenever a note retrigger occurred the module produced a mono sound, although it was set to stereo and width was set to max. After reloading the patch in another session everything worked as expected.rockmachine wrote:I couldn't figure out any reason for why this happened, so this morning, tried another tack. I removed the instance of Zebra while retaining the track data, then loaded a new Zebra and loaded the patch which I had saved and so far, it's not doing what I described yesterday, so here's hoping. So far, so good.