MeldaProduction

Svama · Post by **Svama** » Tue Jan 31, 2017 4:59 pm

Hi Vojtech,

is it possible to add the level meter for the dynamic eq of the band settings page in the band settings (see attachement)? So it´s easier to set the threshold in the band settings itself!

Thanks and greets,
Marek

vectorwarrior · Post by **vectorwarrior** » Tue Jan 31, 2017 6:17 pm

I have wondered the same thing, to use the dynamic EQ effectively you really need to open the settings window. But... there's so many important controls in there that just having the threshold wont be enough anyway... but once it's set up the threshold is the MOST useful.

Svama · Post by **Svama** » Tue Jan 31, 2017 6:19 pm

You could also add the gain reduction in another colour from the right side in this box.

MeldaProduction · Post by **MeldaProduction** » Wed Feb 01, 2017 8:01 pm

I'm afraid no, sorry Marek, development time. It would also consume quite some CPU.

Svama · Post by **Svama** » Wed Feb 01, 2017 9:42 pm

Ok, sadly but no problems. Next question:
Reorder of the frequency nodes? So, that it corresponds with the band view.

Greets,
Marek

Svama · Post by **Svama** » Thu Feb 02, 2017 5:43 am

One more question:

What about an own pop up window for the dynamic section, counterpart to the big band view setting? Would make the thing easier on smaller screens, like laptops.

Marek

MeldaProduction · Post by **MeldaProduction** » Thu Feb 02, 2017 9:13 am

What do you mean by the reorder?? Note that for automation sake the order of bands just cannot be changed.
As for smaller settings, sorry, that's not an option, cluttering the view with yet another settings window. It would probably be possible to make the filter selection and other panels collapsable if that would help.

Svama · Post by **Svama** » Thu Feb 02, 2017 2:51 pm

The button labeled “ORDER BY FREQ” becomes active as soon a band’s FREQUENCY is higher than the previous band. Clicking the button re-orders all band settings by FREQUENCY. Quotation of TDR Nova

MeldaProduction · Post by **MeldaProduction** » Thu Feb 02, 2017 3:28 pm

Hmmm, but what does it do with the automation then? It doesn't make sense really.

Svama · Post by **Svama** » Thu Feb 02, 2017 3:36 pm

Good question. It shouldn't do anything to the automation. It's only the order of the frequency node numbers.

Svama · Post by **Svama** » Thu Feb 02, 2017 3:42 pm

But forget about this feature, if it is too complicated. It´s a nice to have, but not a must!! MTurboReverb and other things are more exciting.

MeldaProduction · Post by **MeldaProduction** » Thu Feb 02, 2017 3:47 pm

Svama · Post by **Svama** » Mon Feb 06, 2017 2:50 pm

Is there a way to change between the different band (nodes) settings inside the band settings view. If not, that would be great, an easy arrow in both directions to toggle between the different bands.

jmg8 · Post by **jmg8** » Mon Feb 06, 2017 2:56 pm

Svama wrote:Is there a way to change between the different band (nodes) settings inside the band settings view. If not, that would be great, an easy arrow in both directions to toggle between the different bands.

Agree, I have wanted to do this a few times in the past. Not essential though.

Svama · Post by **Svama** » Mon Feb 06, 2017 3:03 pm

Would really save some clicks.
Seeing all band node numbers in the band settings view for changing between them would also be nice, so you need less clicks to toggle between different bands.

MeldaProduction

KVR Audio

FR: MDynamicEq´s