Switch LFO destinations
-
- KVRAF
- 1925 posts since 29 Mar, 2013
For some reason it doesnt appear correctly now even though it still works so have added a project so you can see it working
You do not have the required permissions to view the files attached to this post.
Beauty is only skin deep,
Ugliness, however, goes right the way through
Ugliness, however, goes right the way through
-
- KVRAF
- Topic Starter
- 3161 posts since 28 Mar, 2008 from a Galaxy S7 far far away
You lot are going too quick for me!!
Thanks for your help though.
I'm trying to integrate this into my setup to create a variable waveform LFO (still trying to get all waveforms, like Step Up/Down, Noise/Random) with a front panel knob config to adjust between the destinations.
Thanks for your help though.
I'm trying to integrate this into my setup to create a variable waveform LFO (still trying to get all waveforms, like Step Up/Down, Noise/Random) with a front panel knob config to adjust between the destinations.
-
- KVRAF
- Topic Starter
- 3161 posts since 28 Mar, 2008 from a Galaxy S7 far far away
Ok I'm stumped! How is it that adding this to my polysynth module doesn't work until I connect the event input to it? Yet yours sounds though it has no connections?
-
- KVRian
- 877 posts since 28 Feb, 2015 from Interstella 5555
a brilliant idea!!bibz1st wrote:No problem, we now have pads to select the correct mod outputs
you are the master of the randomizer module!
looking at your example I made another 8-way switch for modulation,Thank you bibz1st
sl23 wrote:You lot are going too quick for me!!
Thanks for your help though.
I'm trying to integrate this into my setup to create a variable waveform LFO (still trying to get all waveforms, like Step Up/Down, Noise/Random) with a front panel knob config to adjust between the destinations.
no problem, we can help yousl23 wrote:Ok I'm stumped! How is it that adding this to my polysynth module doesn't work until I connect the event input to it? Yet yours sounds though it has no connections?
check the attached project,open the polysynth and you can see how it works,
Simply connect one of eight outputs(out1,out2..etc.) to whatever you want.
You do not have the required permissions to view the files attached to this post.
-
- KVRAF
- Topic Starter
- 3161 posts since 28 Mar, 2008 from a Galaxy S7 far far away
Thanks so much for your help. I may need further assistance if I may be so bold as to ask 
I agree with Andreas, I would appreciate a switch module too. With up to 8 outputs which cycle via a button press on the front panel. Options to select how many outputs in use, knob/slider or button, display to show current destination.
I agree with Andreas, I would appreciate a switch module too. With up to 8 outputs which cycle via a button press on the front panel. Options to select how many outputs in use, knob/slider or button, display to show current destination.
-
- KVRian
- 877 posts since 28 Feb, 2015 from Interstella 5555
If you need help please ask, there is no problemsl23 wrote:Thanks so much for your help. I may need further assistance if I may be so bold as to ask
I agree with Andreas, I would appreciate a switch module too. With up to 8 outputs which cycle via a button press on the front panel. Options to select how many outputs in use, knob/slider or button, display to show current destination.
a switch module is definitely a good thing ,indeed each new module is definitely a good thing
-
- KVRAF
- 13863 posts since 24 Jun, 2008 from Europe
1 to Many and Many to 1 Switch modules are on the long wishlist.
In fact there should be 3 types of such modules: Audio, Event and Modulation.
So that's 6 modules in total.
I assume you guys will also want the switch parameter to be automatable.
And i assume it would be handy that for audio and moduation that there is an optional "Smooth" parameter that smoothes the transition from switch position X to Y so to avoid unwanted clicks.
All together, it will take some work.
In fact there should be 3 types of such modules: Audio, Event and Modulation.
So that's 6 modules in total.
I assume you guys will also want the switch parameter to be automatable.
And i assume it would be handy that for audio and moduation that there is an optional "Smooth" parameter that smoothes the transition from switch position X to Y so to avoid unwanted clicks.
All together, it will take some work.
-
- KVRAF
- Topic Starter
- 3161 posts since 28 Mar, 2008 from a Galaxy S7 far far away
-
- KVRAF
- Topic Starter
- 3161 posts since 28 Mar, 2008 from a Galaxy S7 far far away
Hey Taifunk, I got a problem with that 8sw patch! For some reason I only have sound when Pad/Switch 2 is active? I checked all connections and all parameters/modules, though I may have missed something. The monitors are active for each pad but no sound is going through. I just can't find the problem! It's probably something simple, I hope, would you mind taking a look please?
Thanks.
I've uploaded it here...
Thanks.
I've uploaded it here...
You do not have the required permissions to view the files attached to this post.
-
- KVRian
- 877 posts since 28 Feb, 2015 from Interstella 5555
No problem, Checked
I found the problem,the oscillator amplitude modulation requires an additional offset on/off.
I describe what I've done:
go in polysynth > open the modulation mapper"OUT 2" > drag the control "offset" in the second polysynth meta-parameters (2),
when the edit mapping appear > set the minimum to 100% and the maximum to 0% and press ok. Now,This happens when you turn on the second pad and after you press another pad,
when the pad 2 is active the offset brings the volume to 0 and increases the modulation source to 100%,
instead the opposite happens when you turn off(by selecting another pad).
I found the problem,the oscillator amplitude modulation requires an additional offset on/off.
I describe what I've done:
go in polysynth > open the modulation mapper"OUT 2" > drag the control "offset" in the second polysynth meta-parameters (2),
when the edit mapping appear > set the minimum to 100% and the maximum to 0% and press ok. Now,This happens when you turn on the second pad and after you press another pad,
when the pad 2 is active the offset brings the volume to 0 and increases the modulation source to 100%,
instead the opposite happens when you turn off(by selecting another pad).
You do not have the required permissions to view the files attached to this post.
-
- KVRAF
- Topic Starter
- 3161 posts since 28 Mar, 2008 from a Galaxy S7 far far away
Wow that was quick! Thank you for checking. I'll take a look when I get home from work.