KVR Audio

incubus · Post by **incubus** » Wed Apr 26, 2017 9:36 am

I guess it's ok to post this now:

Got it for just over 300 USD. Why this one? The neck

Took me a couple of hours of polishing the fret ends but it's like a glove. Sound is ok, but ordered these:

http://nordstrandpickups.com/products/mm5-2/

and

http://nordstrandpickups.com/products/2b-mm-preamp/

Here is a vid showing the before and after tone

Haven't found any cracks in the neck or defects......YET

PurpleCatfishBettie · Thu Apr 27, 2017 11:45 am

that's a great bass

Mister Natural · Post by **Mister Natural** » Thu Apr 27, 2017 6:54 pm

happy new bass day !

Winstontaneous · Post by **Winstontaneous** » Thu Apr 27, 2017 7:33 pm

incubus wrote:
http://nordstrandpickups.com/products/mm5-2/

and

http://nordstrandpickups.com/products/2b-mm-preamp/

Be sure to wire up a 3 way switch (series, parallel, single coil) to get the most out of that pickup. Not sure why Leo Fender chose parallel as the default for StingRay pickups, series has a lot more going on.

incubus · Post by **incubus** » Thu Apr 27, 2017 8:21 pm

Winstontaneous wrote:
incubus wrote:
http://nordstrandpickups.com/products/mm5-2/

and

http://nordstrandpickups.com/products/2b-mm-preamp/

Be sure to wire up a 3 way switch (series, parallel, single coil) to get the most out of that pickup. Not sure why Leo Fender chose parallel as the default for StingRay pickups, series has a lot more going on.

I've thought about that but the wiring is "pre" made for the cut outs in this bass specifically.

And thanks @ well wishes to the others

PurpleCatfishBettie · Thu Apr 27, 2017 10:36 pm

you want to put hpf on the tone, or lpf, or both, depending on the knob position?

PurpleCatfishBettie · Thu Apr 27, 2017 10:37 pm

ooh... 3 knobs... lots of possibilities...

resynthesis · Post by **resynthesis** » Thu Apr 27, 2017 11:06 pm

And, if your soldering is up to it, not too difficult to make for the bass of your choice (or put it into a pedal)

The guitar version (from the Sabre) is similar:

incubus · Post by **incubus** » Fri Apr 28, 2017 2:39 am

resynthesis wrote:And, if your soldering is up to it, not too difficult to make for the bass of your choice (or put it into a pedal)

The guitar version (from the Sabre) is similar:

I can't view those pictures.

incubus · Post by **incubus** » Fri Apr 28, 2017 2:41 am

Xiangqi wrote:ooh... 3 knobs... lots of possibilities...

Well, I didn't want anything that wasn't made to fit this bass (i.e., drilling holes)

So, volume/bass/treble was what it was made for.

resynthesis · Post by **resynthesis** » Fri Apr 28, 2017 9:29 am

incubus wrote:
resynthesis wrote:And, if your soldering is up to it, not too difficult to make for the bass of your choice (or put it into a pedal)

The guitar version (from the Sabre) is similar:

I can't view those pictures.

That's weird. here's a link to the thread on FSB if that helps. The images are on the first page

http://www.freestompboxes.org/viewtopic.php?f=13&t=431

nix808 · Post by **nix808** » Fri Apr 28, 2017 9:50 am

mmm,
I can't see them either.

The board requires reg

Image Shack doesn't fail AFAIK

resynthesis · Post by **resynthesis** » Fri Apr 28, 2017 10:34 am

Ack, sorry, I'm always signed in on FSB so I didn't know it's all registration now. I'll have to get one of those image account things. This work?

nix808 · Post by **nix808** » Fri Apr 28, 2017 11:32 am

Yeah thanks!

I gotta get into guitar electronics,
it's simple at the start level, so seems a neat way to get into electronics

I just wired an active 13-pin hexaphonic pup, and made it passive 7-pin

nix808 · Post by **nix808** » Fri Apr 28, 2017 6:23 pm

Here is the pickup before I put the adapter in the control cavity->

Your next guitar?