I have enabled MIDI program change in MIDI preset switch settings but it doesn't work for me. Using Bitwig's MIDI Program Change device (which has worked successfully for other synths) and also tried pizMIDI's plugin with no luck.
Not much mention of how it works in the manual either.
If you have any tips, appreciate you sending them my way!
Greg K.
Can't get program change to work in MGranularMB
-
- KVRAF
- 2454 posts since 5 Oct, 2003
-
- KVRAF
- 10376 posts since 2 Sep, 2003 from Surrey, UK
Just tried in MMorph here. All OK
Click on [Midi], select the "Preset Switch" tab , enable the "Program change ..." panel AND type in the name of the folder (in the plug-ins Preset browser) where your desired presets are. You may need to build that set of presets in the folder first.
I just chose one of the factory folders:
I see that your other post on this was locked.
---------------------
Edit: Just tried MGranularMB - that is working OK here too.
Click on [Midi], select the "Preset Switch" tab , enable the "Program change ..." panel AND type in the name of the folder (in the plug-ins Preset browser) where your desired presets are. You may need to build that set of presets in the folder first.
I just chose one of the factory folders:
I see that your other post on this was locked.
---------------------
Edit: Just tried MGranularMB - that is working OK here too.
-
- KVRAF
- 10376 posts since 2 Sep, 2003 from Surrey, UK
info wrote: Program change in presets panel enables the MIDI program change processing. If disabled, the plugin follows Program Change messages by changing the A-H presets. The obvious disadvantage is that this way there are just 8 presets.
By enabling this feature the plugin stops selecting A-H presets and rather loads different presets from the specified preset folder, including all sub-folders. The default folder is called "Programs". To use it, you simply need to create a preset folder called Programs and put the presets into it. Note that the order matters of course. And you can change the folder name at any time, so you can have several sets of selectable presets.
Folder
Folder defines the preset folder from which the presets for program-change MIDI messages are taken.
-
- KVRAF
- Topic Starter
- 2454 posts since 5 Oct, 2003
Thanks so much for this! It still isn't working for me and I set it up exactly as you described here (as far as I can tell). I have MMorph also. What DAW are you using?DarkStar wrote:Just tried in MMorph here. All OK
Click on [Midi], select the "Preset Switch" tab , enable the "Program change ..." panel AND type in the name of the folder (in the plug-ins Preset browser) where your desired presets are. You may need to build that set of presets in the folder first.
I just chose one of the factory folders:
I see that your other post on this was locked.
---------------------
Edit: Just tried MGranularMB - that is working OK here too.
-
- KVRAF
- 10376 posts since 2 Sep, 2003 from Surrey, UK
Reaper v5 and its ReaControlMIDI plug-in. And have just tried it in Tracktion 7 too.
If nothing is changing are you sure that the Program Change messages are actually getting to the plug-in? Try inserting a MIDI Monitor immediately before the plug-in.
If nothing is changing are you sure that the Program Change messages are actually getting to the plug-in? Try inserting a MIDI Monitor immediately before the plug-in.
-
- KVRAF
- Topic Starter
- 2454 posts since 5 Oct, 2003
Works now! Thank you! Don't know what was up but I closed Bitwig and freshly set it up again and it worked this time! must've glitched cause I set it up exactly the same way. Or so I think. Also works in Waveform. Thanks for showing how to set it up correctly DarkStar!
-
- KVRAF
- 10376 posts since 2 Sep, 2003 from Surrey, UK