Bug? MHarmonizer Width

[ericzang]

I think I found a bug. Width does not reset to 0 under this circumstance:

Set Mode to Granular (or Adaptive Granular).
Set any shift parameter to any non zero amount.
Set Width to non zero.
Reset Width to zero = width is not reset.

This does not happen in Vocoder or Harmonizer mode.

Thanks for checking it out!

[jmg8]

Working fine here.
I followed your steps.
However I'm not sure what you mean here "Set any shift parameter to any non zero amount"

What do you mean "Any shift parameter"?
There is only 1 shift parameter called "Formant shift" and it is not available in granular mode.

[ericzang]

Sorry, I generalized the term. I meant any of the pitch parameters such as:
Octaves
Semitones
Cents
Pitch

or a keyboard key other than C0.

What I mean by not reset is that although the parameter goes back to 0, the sound does not return to mono.

[jmg8]

Oh, hang on then, I will try again. I only checked visually not audibly.

[jmg8]

Sorry, it still works fine here for me, I am unable to reproduce this.
What version are you using?

[ericzang]

Win 7
Reaper 5.92
Melda 12.03
vst2 and vst3

Here's a simple starting preset. Setting Width to zero while playing audio does not return the sound to mono. Stopping and starting Reaper will properly reset the sound to mono if Width is at 0. Only granular mode behaves this way.

Code: Select all

$eNrdVttu4jAQfd+vsNzXtnEClCIVVlxbtGWLCts+u4kBq46NbIct+-U7dgiEtHuVVlo1D4k9Mz45ZzxO5urjSyrQhmnDlWzj8JxgxGSsEi6XbZzZxdkl-tj5cDW5oTpVkn9jetIzzFrwG3QCKzDqa2WMAoyJSlgbR-WkF6jYlhzz7RocXUmFWoI505pJO9UMgMYDwDh7ojLBaKC3j8x2FwsWWzOW68xeUy79O66-jGfw8qiNW43G6UWzvjcNqdmCmZwC81sun2EIg-vZWnBrmXYhYRs3W82qFRbVIPSh0N68bEaE4M7VnrYjvAXF6JHLRH3NVdxQKSEI2C+4AChIBMwUlxaNBF2aHvCtA+MXl80aCUnUarUaFxc4+FFYvRoWVMC1ihkw0gQNJX0SLPEpGXEh-GC+4rGXHZRiQ9RXQmkwk26fkNEI5waXql7rsj5wljsQqXnCdqE-wooKLId0jAVIQ9L7A6xaGavbP8YivUb9D7DqZaxGt4oVRr-GCl5tNhS7q0ayK+6TT4ytR0qnVFrja+skL-NrTWUmqAbDlNt4Bb5zUr+E6SNPbD5tXWCUH5yt24i3r5D8+sJoBodGZTLpr6D+mDB5JQDF3QUlWYQ8KJGlDMR1B7N75G5zlq7VbCvjNr5bLDDqWkt9Cs5JWMxmK+rKG141YDHdFk4-KfuE94EuJRI-uGeCUcP8gsZ+elgyS5WyK-898TqM9YeanENwhVjnaq5ZChvlV6M80Z9d8gVGGyoymDacUsvWoO9uzTS1cHiN28nyUpg63fDwewl7eju6Mx13J8ewUE5U05TBYUOjTIh7Kpc57739MzzaGD5OAXydXNEM5YYJtXYpnvEl1M3PmaKxZSl8g84gnW5YOwwbh2HTD1+pyl8AQJAkdMvk0pVW5EvXifGSwvckKfSSovckKfKSau9JUi1-GDhZfSWtVkLAf7RTmlR+VgeF0c8UBmU0aDsyYfk+GvCPDcQ1AcOEW7XrPXoc+ovjnDzkOQl3o9w5ZTqGFsT81S4EFRJVVuH-wCqssop+nxX5Z6yiKqva-8Cq9sriaq8bW75heZda9Kxl21guVBvjt1z5CzFywtwmB66UdxXsu4MJnCuVgQJUbvWKnqQImTL6HM7RAzfc-+u995Fu2AIy88oRTArmwZvdeufDd7HFyJw=

[MeldaProduction]

I think that's actually normal, it's a phase relationship problem - it cannot be done without a "click", so I'd suggest simply adding say MStereoSpread afterwards.

[ericzang]

ok thanks, it's not a problem for me anyhow.