KVR Audio

vurt · Post by **vurt** » Fri Sep 17, 2021 12:35 pm

elxsound wrote: ↑Fri Sep 17, 2021 12:24 pm No lizards?

i teleported a disco alien! and you want lizards!!!?

whyterabbyt · Post by **whyterabbyt** » Sat Sep 18, 2021 4:10 am

vurt wrote: ↑Fri Sep 17, 2021 12:35 pm
elxsound wrote: ↑Fri Sep 17, 2021 12:24 pm No lizards?

i teleported a disco alien! and you want lizards!!!?

What about wizards?

Or gizzards?

Or Eddie Izzards?

methinks you're just not trying.

vurt · Post by **vurt** » Sat Sep 18, 2021 5:00 am

done wizards.

justin3am · Post by **justin3am** » Tue Sep 21, 2021 8:29 am

justin3am wrote: ↑Mon Jan 25, 2021 9:20 am I got my second CVz from Perfect Circuit over the weekend. This one is in a 4MS pod and is replacing the passive matrix mixer on my main pedal board. Matrix mixers, sequential switches and panners have myriad uses on a pedal board. But now I'm realizing that I need stackable 1/4" patch cables!

Just realized I never posted a picture of this setup in a place where Urs might see it...

Wanterkeelt · Post by **Wanterkeelt** » Wed Oct 20, 2021 5:02 am

Hi,
I do have one question about CVilization's quatizer specs and especially its accuracy. I recently stumbled about this page https://doudoroff.com/quantizers/ where they compare lots of quantizers and say:
"The Nominal accuracy column is a simple calculation of the resolution of the DAC against the output range of the quantizer. There are many other factors that may relate to the accuracy of a quantizer, but this is a baseline. Note that a cent is 0.83 millivolts, so quantizers above that value lack the resolution to be accurate within a cent."
Unfortunately CVilization is not listed in the products, so maybe someone has done a similar test already or Urs can tell us about it a little more ?
Thanks in advance

Urs · Post by **Urs** » Wed Oct 20, 2021 5:20 am

CVilization has 24 bit converters. They are way better than Cent accuracy (even at +/- 10V ranges)

Wanterkeelt · Post by **Wanterkeelt** » Wed Oct 20, 2021 9:05 am

Ah that's perfect, thanks

mikeleebirds · Post by **mikeleebirds** » Tue Feb 15, 2022 1:10 am

elxsound wrote: ↑Tue Jun 15, 2021 7:48 pm Has anyone asked for a black plate version?

I have and they said "no".

Urs · Post by **Urs** » Tue Feb 15, 2022 2:01 am

mikeleebirds wrote: ↑Tue Feb 15, 2022 1:10 am
elxsound wrote: ↑Tue Jun 15, 2021 7:48 pm Has anyone asked for a black plate version?
I have and they said "no".

But they do try.

neuromod · Post by **neuromod** » Fri May 27, 2022 8:21 pm

What is the significance of the color of the LEs in mode 3? I've got two CVilizations and one of them the encoders are amber, and the other they're a lovely sort of turquoise. Did I configure the "visual range" for one of them in the config file? I don't recall so doing, but it's also not clear to me what that parameter refers to.

Urs · Post by **Urs** » Fri May 27, 2022 11:35 pm

Teal means a random value (nothing patched/normalled into the channel), amber means it did get a CV patched in which it is sampling and holding.

neuromod · Post by **neuromod** » Sat May 28, 2022 9:52 am

Oh, it turns out I was referring to sequence length. I had set all channels of the one I had been using in mucorder to 8 steps, and then forgot I had done that set-up step when setting up the second CVilization to also operate in that mode. I feel dumb for going to the forum with such an obvious the-manual-would-have-cleared-this-up question. Oh, well.

Urs · Post by **Urs** » Sat May 28, 2022 3:25 pm

Hahaha, ok, it an 8-pixel display is not the most intuitive thing possible... I wasn't too sure, either.

neuromod · Post by **neuromod** » Sat May 28, 2022 4:19 pm

I like the teal! I may need to start using 1-step sequences for aesthetics.

U-he Hardware - CVilization Eurorack Module