KVR Audio

Erisian · Post by **Erisian** » Mon Aug 08, 2022 10:20 am

OK, here is where I show my utter stupidity and ineptitude. How on earth do I route an LFO to the filter to create a filter sweep? I tried looking in the manual but it wasn't clear to me.

Chris-S · Post by **Chris-S** » Mon Aug 08, 2022 10:34 am

Set up filter1 to be a 24 dB lowpass, put cutoff to middle position,
click on LFO1 in the blue-section until it's green (armed), slide the cutoff-knob to the desired modulation amount, click again on LFO1, done.

Iu Gob · Post by **Iu Gob** » Mon Aug 08, 2022 10:36 am

Funkybot's Evil Twin wrote: Fri Aug 05, 2022 1:23 pm Congrats on the big release Surge Team! Great job! Incredible effort and collaboration.

+1

Erisian · Post by **Erisian** » Mon Aug 08, 2022 10:45 am

Chris-S wrote: Mon Aug 08, 2022 10:34 am Set up filter1 to be a 24 dB lowpass, put cutoff to middle position,
click on LFO1 in the blue-section until it's green (armed), slide the cutoff-knob to the desired modulation amount, click again on LFO1, done.

Awesome - thank you!

robindrieghe · Post by **robindrieghe** » Tue Aug 09, 2022 11:13 pm

are the old patches available somewhere?

baconpaul · Post by **baconpaul** » Tue Aug 09, 2022 11:41 pm

We've not removed any patches from the day it was open sourced. They are all in the installer.

Halonmusic · Post by **Halonmusic** » Wed Aug 10, 2022 1:54 am

in the osc section, particularly the Twist mode, some of the sliders are greyed out/doesn't do anything. Is that intended?

baconpaul · Post by **baconpaul** » Wed Aug 10, 2022 2:51 am

Halonmusic wrote: Wed Aug 10, 2022 1:54 am in the osc section, particularly the Twist mode, some of the sliders are greyed out/doesn't do anything. Is that intended?

Right mouse and you can enable them

Halonmusic · Post by **Halonmusic** » Wed Aug 10, 2022 6:00 am

baconpaul wrote: Wed Aug 10, 2022 2:51 am
Halonmusic wrote: Wed Aug 10, 2022 1:54 am in the osc section, particularly the Twist mode, some of the sliders are greyed out/doesn't do anything. Is that intended?
Right mouse and you can enable them

thanks

EvilDragon · Post by **EvilDragon** » Wed Aug 10, 2022 8:21 pm

baconpaul wrote: Tue Aug 09, 2022 11:41 pm We've not removed any patches from the day it was open sourced. They are all in the installer.

We did remove a couple (at sound designer's request), and renamed a bunch, though.

Chris-S · Post by **Chris-S** » Sat Aug 13, 2022 12:58 pm

SYNC
Normally when using (hard) sync the oscillator-timbre is changed but the tone frequency is stay'ing the same. Not so on Surge:

surgesyncbug.jpg

Tone is going down one octave. Is this intended or maybe a restriction of the implementation?
In case of using square waves I found a workaround: When using the Sub Osc (Sub Mix=100%) all is correct.

EvilDragon · Post by **EvilDragon** » Sat Aug 13, 2022 2:56 pm

It's just how internal sync oscillator has been implemented for Classic and Modern, I think.

baconpaul · Post by **baconpaul** » Sat Aug 13, 2022 3:33 pm

yeah classic uses a half rate sync wave and we decided to be consistent in modern. I suppose we could make a sync deform option in modern which used a full rate sync wave though! (but we can't in classic for a fiddly reason i forget).

mabian · Post by **mabian** » Sat Aug 13, 2022 4:28 pm

Is there an expected date for the next (bug fix only I guess) 1.1.x version?

I see some buglets have sneaked into 1.1.0 so I'd like to wait a bit until these are ironed out as well...

Thanks,
Mario

EvilDragon · Post by **EvilDragon** » Sat Aug 13, 2022 6:01 pm

2-4 weeks, but take this with a grain of salt - we don't do deadlines! Don't be afraid to use Surge as is. There will always be bugs. These are not catastrophic.

Vember Audio Surge is now open-source