DrivenByMoss: Bitwig extension for many hardware controllers (version 26.6.1)

[moss]

Dear Moss.

I would like to create a controller that uses TouchOSC to directly manipulate the track parameters of each track.
Is there a way to specify a track and send track parameters, like when manipulating send levels?

Thank you.

Yes. All commands can be found in the OSC chapter in the DrivenByMoss manual. There are also several OSC tutorial videos on my Youtube channel.

[Koldunya]

,.....................,

[Clearscreen]

Is you website down Moss? Can't get it to load here... Is your work available on github, or only the source code? Also, as always, thanks for your work

[Watto85]

I also cant get mossgrabers.de to load...

[moss]

I also cant get mossgrabers.de to load...

I switched my domain provider yesterday. Might take a bit till it works all over the world.
For the time being you can access it directly: https://92.205.106.63/

[flyingbaron]

Dear Moss.

I would like to create a controller that uses TouchOSC to directly manipulate the track parameters of each track.
Is there a way to specify a track and send track parameters, like when manipulating send levels?

Thank you.

Yes. All commands can be found in the OSC chapter in the DrivenByMoss manual. There are also several OSC tutorial videos on my Youtube channel.

Thank you for your response.
But sorry, I am not sure I am communicating what I want to do.
I want to use TouchOSC to directly manipulate track parameters of an unselected track.
But I could not find in the DrivenByMoss documentation how to manipulate the parameters by specifying the target track.
I tried using the TouchOSC script to select the track and then manipulate the parameters, but each operation switches the active track.
What is the best way to do this?

[moss]

Dear Moss.

I would like to create a controller that uses TouchOSC to directly manipulate the track parameters of each track.
Is there a way to specify a track and send track parameters, like when manipulating send levels?

Thank you.

Yes. All commands can be found in the OSC chapter in the DrivenByMoss manual. There are also several OSC tutorial videos on my Youtube channel.

Thank you for your response.
But sorry, I am not sure I am communicating what I want to do.
I want to use TouchOSC to directly manipulate track parameters of an unselected track.
But I could not find in the DrivenByMoss documentation how to manipulate the parameters by specifying the target track.
I tried using the TouchOSC script to select the track and then manipulate the parameters, but each operation switches the active track.
What is the best way to do this?

Ah, you mean the new track parameters. No, that is not supported.

[flyingbaron]

Dear Moss.

I would like to create a controller that uses TouchOSC to directly manipulate the track parameters of each track.
Is there a way to specify a track and send track parameters, like when manipulating send levels?

Thank you.

Yes. All commands can be found in the OSC chapter in the DrivenByMoss manual. There are also several OSC tutorial videos on my Youtube channel.

Thank you for your response.
But sorry, I am not sure I am communicating what I want to do.
I want to use TouchOSC to directly manipulate track parameters of an unselected track.
But I could not find in the DrivenByMoss documentation how to manipulate the parameters by specifying the target track.
I tried using the TouchOSC script to select the track and then manipulate the parameters, but each operation switches the active track.
What is the best way to do this?

Ah, you mean the new track parameters. No, that is not supported.

I'm sorry I can't express myself well in English.
What I want to do is to directly manipulate the parameters of each track as shown in the image.

control image.jpg

[moss]

Dear Moss.

I would like to create a controller that uses TouchOSC to directly manipulate the track parameters of each track.
Is there a way to specify a track and send track parameters, like when manipulating send levels?

Thank you.

Yes. All commands can be found in the OSC chapter in the DrivenByMoss manual. There are also several OSC tutorial videos on my Youtube channel.

Thank you for your response.
But sorry, I am not sure I am communicating what I want to do.
I want to use TouchOSC to directly manipulate track parameters of an unselected track.
But I could not find in the DrivenByMoss documentation how to manipulate the parameters by specifying the target track.
I tried using the TouchOSC script to select the track and then manipulate the parameters, but each operation switches the active track.
What is the best way to do this?

Ah, you mean the new track parameters. No, that is not supported.

I'm sorry I can't express myself well in English.
What I want to do is to directly manipulate the parameters of each track as shown in the image.
control image.jpg

Yes, that is what I understood. I decided against supporting this since it would cause a lot of additional messages.

[brainztain]

Hello Mr. Moss and thank you for sharing your creation.

On Akai Fire, bitwig crashes when changing note lengths in note edit mode with the knobs.

This happens if notes overlap after increasing their length. The notes also disappear on the software but not on the Akai fire. The crash happens only sometimes after notes disappear.

I've tried latest two versions and got the same results. I've also searched here and found one mention of it but no replies.

Any solutions for this?

Thanks again!

[flyingbaron]

I'm sorry I can't express myself well in English.
What I want to do is to directly manipulate the parameters of each track as shown in the image.

Yes, that is what I understood. I decided against supporting this since it would cause a lot of additional messages.

Thank you for your help.
I understand that I cannot do this operation.

[joris.roling]

Hi @moss, it seems your site http://www.mossgrabers.de is down.

[moss]

Hi @moss, it seems your site http://www.mossgrabers.de is down.

I switched my domain provider. Just got the routing fixed. Should work again latest tomorrow (fingers crossed!).
For the time being you can access it directly: https://92.205.106.63/

[moss]

Hello Mr. Moss and thank you for sharing your creation.

On Akai Fire, bitwig crashes when changing note lengths in note edit mode with the knobs.

This happens if notes overlap after increasing their length. The notes also disappear on the software but not on the Akai fire. The crash happens only sometimes after notes disappear.

I've tried latest two versions and got the same results. I've also searched here and found one mention of it but no replies.

Any solutions for this?

Thanks again!

Please give some specific steps to reproduce this. I fiddled around with this a bit but could not create a crash.

[darougeadam]

Hey Jurgen, thanks for your work!
I'm using your script on icon p1-m+ extender and it works very well, better than Bitwig one's.
there's only one thing I think it's missing, I can't figure out the way to switch between devices pages controls, while in Bitwig's you can switch between pages with up/down function it doesn't in yours.

Also, it would be nice to take advantage of the extender(/s) to show more than one page at the time.
Thanks for your time.

They are changed with the CHANNEL LEFT/RIGHT buttons. If I see that correctly iCON did not add these buttons to the P1-M?! But you should be able to program them on this new touch display.

You are right, i felt like a bad person after re-reading the manual and realizing i missed it, sorry for that.

Is the possibility of showing more than one bank at time something that can be implemented?

Thanks for your work and have a good day!